Related Manuals for Officine Gullo GEFS8P
Summary of Contents for Officine Gullo GEFS8P
- Page 1 INSTRUCTIONS FOR INSTALLATION AND USE GEFS8P RANGE WITH OVEN FOR RESIDENTIAL AND PROFESSIONAL USE...
- Page 2 14. In case of failure or malfunction, turn the appliance off, close the gas supply valve and do not attempt to carry out any repairs, which must be done exclusively by an authorized service center. Request the use of original spare parts only. Failure to comply with the above recommendations may compromise the appliance’s safety. Officine Gullo...
-
Page 3: Table Of Contents
WHAT TO DO IN THE EVENT OF A BREAKDOWN ..............16 PROCEDURE TO FOLLOW IF THE APPLIANCE IS NOT GOING TO BE USED FOR SOME TIME ..16 MAINTENANCE (only for qualified personnel) ................16 INSTRUCTIONS FOR DISCHARGING GAS EMISSIONS ............17 COOKING TABLE FOR THE FAN OVEN .................18 Officine Gullo... -
Page 4: Installation Manual
INSTALLATION MANUAL Fig. A/1 GEFS8P 73 cm 70 cm 3 cm 4 cm (1/2") (1/2") 20 cm 42 cm 10 cm 67 cm 80 cm Su richiesta accensione con fiamma pilota Also available with pilot flame LEGEND Electric connection/Connessione lettrica... - Page 5 Einspritzventil flamme Injecteur feux Injector cooking rings Inyector fuegos Regolazione aria Luftregelung Réglage d'air Air regulation Regulación aire 2. Air regulation 4. Thermocouple Candela accensione Zündkerze Bougie d'allumage Lighting spark plug Candela encendido Termocoppia Thermoelement Thermocouple Thermocouple Termopar Officine Gullo...
- Page 6 Fig. D ELECTRICAL SCHEME TOP Electrical connection Push-button starting burner 3/4. Power-station starting burner Officine Gullo...
- Page 7 Fig. I WIRING DIAGRAM FAN OVEN Commutator Capacitor Power supply terminal Terminal board switching Engine Element White light Green light Safety thermostat 10. Thermostat Officine Gullo...
-
Page 8: Declaration Of Compliance
DECLARATION OF COMPLIANCE This appliance is manufactured by OFFICINE GULLO S.r.l Headquarters and factory Via Della Torricella 29, Antella, Bagno a Ripoli 50012 Florence - Italy Tel. +39 055 65 60 3324 +39 055 62 18 07 officinegullo.com | info@officinegullo.com The manufacturer declares that the appliances are compliant with the prescriptions of the EEC norm 2009/142 for the gas part and with norm 2006/95/CE, 2004/108/CE for the electric part. -
Page 9: Installation
Take suitable measures to guarantee thermal insulation of the inflammable sides, such as, for example, the installation of protection against radiation. The appliances must be installed in a suitable manner, observing the safety standards. The small feet are adjustable to level the appliance. Officine Gullo... -
Page 10: Pipe For Gas Connection
The connection screw is positioned at the back of the appliance and is identified by the symbol Attention! The manufacturer will neither be held responsible for, nor will give any compensation during the guarantee period for any damage caused, and which is due to inadequate installations not compliant with the instructions. Officine Gullo... -
Page 11: Checking Heat Output
The pilot air is regulated when the appliance is tested and inspected for the gas it is set for. If you are going to change to a different type of gas, regulate the air by means of the adjusting bush until the flame stops sputtering and becomes an intense blue colour. Officine Gullo... -
Page 12: Burner Technical Data Table
Air adjustment (mm) Burner max 7,5 kW- min. 2,5 kW Injector (marking) By-pass (screw asjustment (number of turns anti- 1+1/2 1+1/2 3+1/2 clockwise from fully closed position) Air adjustment (mm) 10,0 10,0 10,0 Officine Gullo... -
Page 13: Rules For Converting And Installing Other Types Of Gas
SPARE PARTS Open rings: The cocks can be changed by removing the front panel; to change the thermocouples and burners you have to remove the rungs and trays. Officine Gullo... -
Page 14: User Manual
Since the oven chamber is heated evenly, different foods can be cooked together on different rungs Turn the knob from ”O” into the desired position between 50° and 300°; The white and green lights come on. The green light indicates the presence of electrical tension. Officine Gullo... -
Page 15: Cleaning And Maintenance
Do not use abrasive pads or any other chemical products. Cleaning brushed steel surfaces All the brushed steel surfaces should be cleaned using degreasing products or products specifically designed to be used on steel and, where necessary, extra-fine steel wool or extra-thin sandpaper. Officine Gullo... -
Page 16: What To Do In The Event Of A Breakdown
Turn off the gas tap and clean the appliance as specified above. MAINTENANCE (only for qualified personnel) Any kind of maintenance must only be done by qualified personnel. Before carrying out maintenance,remove the plug or switch off the switch above the appliance. Officine Gullo... -
Page 17: Instructions For Discharging Gas Emissions
4.3 of the UNI-CIG norm 8723. Supplying the appliance with gas again must only be possible manually. NATURAL DISCHARGE FORCED DISCHARGE Fig.1 Fig.2 1. Extractor hood 1. Extractor hood 2. Interlocking Officine Gullo... -
Page 18: Cooking Table For The Fan Oven
Short pastry with a wet filling Short pastry with a dry 1-3-4 filling With a natural leavening dough Small cakes 1-3-4 Meat Grilled roasts Veal Beef English roast beef Pork Chicken 1-1.5 Baking-pan roasts Veal Beef Pork Chicken 1-1.5 Officine Gullo... - Page 19 1-1.5 Casseroles Beef casserole Veal casserole Fish Filets, steaks, cod, hake, sole Mackerel, turbot, salmon Oysters Oven bakes Pasta Vegetables Sweet and savoury 0.75 soufflés Pizza and “calzone” 1-3-4 Toast 1-3-4 Defrosting First courses Meat Meat 0.75 Meat Officine Gullo...
- Page 20 international V 1.0 -7.20 Tel. +39 055 656 0324 | info@officinegullo.com Via Della Torricella 29, Antella, Bagno a Ripoli - 50012 Florence - Italy OFFICINEGULLO.COM...