Page 1
INSTRUCTIONS FOR INSTALLATION AND USE GGS8P - GGS12P - GGPS8P - GGPS12P GES8P - GES12P - GEPS8P - GEPS12P RANGE WITH OVEN FOR RESIDENTIAL AND PROFESSIONAL USE...
WHAT TO DO IN THE EVENT OF A BREAKDOWN ..............28 PROCEDURE TO FOLLOW IF THE APPLIANCE IS NOT GOING TO BE USED FOR SOME TIME ..28 MAINTENANCE (only for qualified personnel) ................28 INSTRUCTIONS FOR DISCHARGING GAS EMISSIONS ............28 Officine Gullo...
DECLARATION OF COMPLIANCE This appliance is manufactured by OFFICINE GULLO S.r.l Headquarters and factory Via Della Torricella 29, Antella, Bagno a Ripoli 50012 Florence - Italy Tel. +39 055 65 60 3324 +39 055 62 18 07 officinegullo.com | info@officinegullo.com The manufacturer declares that the appliances are compliant with the prescriptions of the EEC norm 2009/142 for the gas part and with norm 2006/95/CE, 2004/108/CE for the electric part.
All our appliances undergo careful testing: the type of gas, the operating pressure and the category are indicated on the data plate. NB: The year of the appliance manufacture is shown in item “N” on the data plate. The first two numbers (e.g. 08..) represent the year of manufacture. Officine Gullo...
Connection with natural gas H G20 The connection pressure for natural gas is 20 mbar. Check the plate, read the pressure and verify that the description of the nozzle installed corresponds to the one supplied by the manufacturer. Officine Gullo...
Consumption Primary air h=mm Oven Burner max 11 kW- min. 3,5 kW Burner injector 1/100 mm Min. output adjustment 1/100 mm adjustable Pilot Injector 1x19 1x19 1x27 0.859 kg/h 0.859 kg/h 1.164 m3 st./h Consumption Primary air h=mm Officine Gullo...
Page 22
Air adjustment (mm) 10,0 10,0 10,0 Oven Burner max 6,5 kW- min. 2,2 kW Injector (marking) By-pass (screw asjustment (number of turns anti- clockwise from fully closed position) Air adjustment (mm) 14,0 14,0 14,0 Pilot injector Officine Gullo...
Adjust the minimum flame by turning the by-pass screw either to the right or to the left until heat output reaches 4 kW. The primary air of the all plate burner does not need adjusting. Attention: If liquid gas is used, the minimum flame adjustment screw must be screwed right down. Officine Gullo...
The cocks can be changed by removing the front panel; to change the thermocouples and burners you have to remove the rungs and trays. Gas oven: the gas-cock, timer, thermocouples, burners and ignition plugs can be changed by accessing them inside the oven and/or by removing the bottom oven panel or control panel. Officine Gullo...
If the flame goes out you have to repeat the procedure. By turning the knob round to the position the burner is at maximum. By turning the knob round to the position the burner is at minimum. To switch off, move the knob back into position " 0". Officine Gullo...
30 minutes. All cooking times are based on a preheated oven unless otherwise stated in the recipe. Caution: when the oven is on the door must be kept shut otherwise the knobs and protection sheet could get hot and be damaged. Officine Gullo...
Do not use abrasive pads or any other chemical products. Cleaning brushed steel surfaces All the brushed steel surfaces should be cleaned using degreasing products or products specifically designed to be used on steel and, where necessary, extra-fine steel wool or extra-thin sandpaper. Officine Gullo...
Supplying the appliance with gas again must only be possible manually. NATURAL DISCHARGE NATURAL DISCHARGE FORCED DISCHARGE FORCED DISCHARGE Fig.1 Fig.1 Fig.2 Fig.2 1. Extractor hood 1. Extractor hood 1. Extractor hood 1. Extractor hood 2. Interlocking 2. Interlocking Officine Gullo...
Page 29
FORCED DISCHARGE Fig. 3 Fig. 4 1) Anti-wind (blow back) chimney 1. Extractor hood 2. Interlocking Type “B11” appliances are supplied upon request with chimney or chimney and anti-wind (blow back) device to be assembled and delivered separately. Officine Gullo...