Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Allied Telesis BRKT-J23
- Page 1 BRKT-J23 Wall Mount Kit for Switches Installation Guide 613-003105 Rev. A...
- Page 2 Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been...
-
Page 3: Table Of Contents
Chapter 1: Installation Using the BRKT-J23 Kit ........................9 Introduction..................................10 Unpacking the BRKT-J23 Wall Mount Kit........................12 Installing a Switch Using the BRKT-J23 Wall Mount Kit....................13 What to Prepare ..............................13 Installing a Switch with the Front Panel Facing Sideways ..................13 Installing a Switch with the Front Panel Facing UP....................16 Installing a Switch Using the Four Brackets ......................17... - Page 4 BRKT-J22 Wall Mount Kit Installation Guide...
-
Page 5: Preface
Preface This document contains the installation instructions for the BRKT-J23 wall mount kit. These wall mount brackets are used to install an Allied Telesis switch to a wall. Note Refer to the Installation Guide of your switch if it should be installed using the BRKT-J23 wall mount kit. -
Page 6: Safety Symbols Used In This Document
BRKT-J23 Wall Mount Kit Installation Guide Safety Symbols Used in this Document This document uses the following conventions: Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. -
Page 7: Contacting Allied Telesis
guides, software release notes, white papers and data sheets for your product. Warranty - View a list of products to see if Allied Telesis warranty applies to the product you purchased and register your warranty. Allied Telesis Helpdesk - Contact a support representative. - Page 8 BRKT-J23 Wall Mount Kit Installation Guide...
-
Page 9: Chapter 1: Installation Using The Brkt-J23 Kit
This chapter explains the procedures how to install a switch on a wall using the BRKT-J23 wall mount kit. It contains the following sections: “Introduction” on page 10 “Unpacking the BRKT-J23 Wall Mount Kit” on page 12 “Installing a Switch Using the BRKT-J23 Wall Mount Kit” on page 13 ... -
Page 10: Introduction
BRKT-J23 Wall Mount Kit Installation Guide Introduction The BRKT-J23 wall mount kit allows you to install a switch to a wall. Here are guidelines for installing a switch on a wall using the BRKT-J23 wall mount kit. See the Installation Guide of your switch to find out if your switch ... - Page 11 Chapter 1: Installation Using the BRKT-J23 Kit Figure 2 shows the orientation of the brackets using two sets of the BRKT-J23 wall mount kits. Figure 2. Orientations of the Brackets to a Switch with Four Brackets Figure 3 shows a wrong orientation of the brackets to a switch.
-
Page 12: Unpacking The Brkt-J23 Wall Mount Kit
2. Verify that two brackets are included in your wall mount package listed in Table 1. Table 1. Components in the BRKT-J23 Wall Mount Kit Components Two brackets 3. If any item is missing or damaged, contact your Allied Telesis sales representative for assistance. -
Page 13: Installing A Switch Using The Brkt-J23 Wall Mount Kit
Chapter 1: Installation Using the BRKT-J23 Kit Installing a Switch Using the BRKT-J23 Wall Mount Kit This section shows you steps to install a switch on a wall using the BRKT-J23 brackets. What to Prepare Before installing a switch on a wall, make sure that the following items are ready. - Page 14 BRKT-J23 Wall Mount Kit Installation Guide 4. Have another person hold the switch with the brackets at the location where the switch is to be installed, while you use a pencil to mark the wall at the locations of the four holes in the brackets. See Figure 5.
- Page 15 Chapter 1: Installation Using the BRKT-J23 Kit 8. Make sure that the two brackets are installed securely. 9. Slide the switch into the brackets on the wall as shown in Figure 7. Figure 7. Placing the Switch into the Brackets...
-
Page 16: Installing A Switch With The Front Panel Facing Up
BRKT-J23 Wall Mount Kit Installation Guide Installing a To install the switch on a wall horizontally, install the brackets to support the switch from the sides as shown in Figure 8. Switch with the Front Panel Facing UP Figure 8. Installing the Brackets to Support the Switch... -
Page 17: Installing A Switch Using The Four Brackets
Chapter 1: Installation Using the BRKT-J23 Kit Installing a To install a switch on a wall with the four BRKT-J23 brackets, perform the following procedure: Switch Using the Four Brackets 1. Install the switch using the two BRKT-J23 brackets, See “Installing a Switch with the Front Panel Facing Sideways”... - Page 18 BRKT-J23 Wall Mount Kit Installation Guide 5. Install the four plastic anchors into the holes of the wall. 6. Place the two brackets back on the top of the switch and screw the screws through the holes to attach the brackets on the wall. See Figure 10 as an example.
-
Page 19: Appendix A: Specifications
Appendix A Specifications Physical Specifications Weight (One bracket): 57.6 g (2 oz) Dimensions: Figure 11. BRKT-J23 Height Figure 12. BRKT-J23 Width and Depth... - Page 20 BRKT-J23 Wall Mount Kit Installation Guide...