Herd IN24A2 Installation Manual

Herd IN24A2 Installation Manual

International hx520 sfa, hx615/620 sba

Advertisement

Quick Links

Thank you for choosing HERD!
For assistance call
1-888-543-4373
www.HERD.com
 Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was
designed for will constitute improper use of the product and may void warranty.
 Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these
instructions, OE hardware means the truck's original factory hardware.
 For further detail of warranty coverage and warranty repair information visit

General Safety

 Take time to fully read the instructions before installing the Herd bumper.
 At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.
 Parts and components of the Herd bumper can be heavy, handle with care to avoid injuries.
 Respect power tools and use them as advertised.
Part No: IN24-IG
Rev: A
Date:28-Nov-16
Installation guide
SKU #
IN24A2, IN25A2, IN24A4,
IN25A4, IN24D2, IN25D2,
IN24D4, IN25D4,
IN24DFLT2, IN25DFLT2,
IN24RT, IN25RT, IN24TX4,
IN24BTX4, IN24SRT
1
Truck Model
International
HX520 SFA,
HX615/620 SBA
IN24SRT SHOWN
.
www.HERD.com
HERD North America Inc.
1-888-543-4373
2168 Springfield Road
www.HERD.com
Box 28, Group 525, RR5
Winnipeg, MB. Canada R2C 2Z2
1-888-543-4373

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IN24A2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Herd IN24A2

  • Page 1 IN24SRT SHOWN Important  Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was designed for will constitute improper use of the product and may void warranty.  Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these instructions, OE hardware means the truck's original factory hardware.
  • Page 2 Specification Socket ¾” or 19 mm Socket ” or 24 mm Socket ” or 30 mm Wrench ¾” or 19 mm Wrench ” or 24 mm Wrench ” or 30 mm Part No: IN24-IG 1-888-543-4373 Rev: A www.HERD.com Date:28-Nov-16 1-888-543-4373...
  • Page 3 Remove OEM bumper. Remove this bolt Figure 2 3. Install center mount (Item 4) onto cross member as shown in Figure 3. Cross member Figure 3 – Center mount installation. Part No: IN24-IG 1-888-543-4373 Rev: A www.HERD.com Date:28-Nov-16 1-888-543-4373...
  • Page 4 5, otherwise proceed to step Figure 4a – Herd bracket attached to center mount. Tow receiver casting Figure 4b – Herd bracket attached to tow receiver casting. Part No: IN24-IG 1-888-543-4373 Rev: A www.HERD.com...
  • Page 5 Check mounting points after the first 5000 km and every 3-6 month.  If bumper is equipped with Herd Slam Latch, periodic adjustment is required. Refer to Slam Latch Installation adjustment instructions to properly adjust your Slam Latch. Part No: IN24-IG...

This manual is also suitable for:

In25a2In24a4In25a4In24d2In25d2In24d4 ... Show all

Table of Contents