Advertisement
Quick Links
Thank you for choosing HERD!
For assistance call
1-888-543-4373
www.HERD.com
Important
• Herd Truck Guards are vehicle "Make & Model" specific. Use of a Truck Guard on a vehicle other than the
model it was designed for will constitute improper use of the product and may void warranty.
• Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these
instructions, OE hardware means the truck's original factory hardware.
• For further detail of warranty coverage and warranty repair information visit
General Safety
• Take time to fully read the instructions before installing the Herd Truck Guard.
• At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.
• Parts and components of the Herd Truck Guard can be heavy, handle with care to avoid injuries.
• Respect power tools and use them as advertised.
Part No: KW22C4-02-IG
Rev: B
Date: 2020-04-16
Installation Guide
SKU #
KW22C4-02
1
Truck Model
Kenworth T880
.
www.HERD.com
HERD North America Inc.
2168 Springfield Road
Box 28, Group 525, RR5
Winnipeg, MB. Canada R2C 2Z2
1-888-543-4373
www.HERD.com
1-888-543-4373
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Herd KW22C4-02
Summary of Contents for Herd KW22C4-02
- Page 1 Important • Herd Truck Guards are vehicle "Make & Model" specific. Use of a Truck Guard on a vehicle other than the model it was designed for will constitute improper use of the product and may void warranty. • Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these instructions, OE hardware means the truck's original factory hardware.
- Page 2 WASHER-FLAT 1/4 SAE GR8 YZP 500095 BOLT-HEX 1/4-20X1 NC GR5 WZP 500173 NUT-NYLOCK 3/4-16 NF GR8 YZP 500211 WASHER-FLAT 3/4 SAE GR8 YZP 500085 BOLT-HEX 1/2-13X1-3/4 NC GR8 YZP 100049 WLDMT-TOW PIN Part No: KW22C4-02-IG 1-888-543-4373 Rev: B www.HERD.com Date: 2020-04-16 1-888-543-4373...
- Page 3 If the truck has a collision mitigation radar sensor, unplug and remove it. Refer to the HERD radar sensor installation guide (S009) to re-install your sensor. Remove 3 Bolts Per Side Figure 1 –...
- Page 4 Installation Procedure 4. Install clevis pins (From Item 3) through OEM tow receiver holes and HERD tow receiver mounts. Install hair pins into the clevis pins from the KW22 Mounting Kit (Item 3). Figure 4 – Tow Receiver Clevis & Hair Pins Installation 5.
- Page 5 Remove truck guard and set aside on cardboard. Now the bracket is isolated for mounting without a lift. ” Hardware Figure 7b – Bracket and Truck guard Disassembly (Driver Side Shown) Part No: KW22C4-02-IG 1-888-543-4373 Rev: B www.HERD.com Date: 2020-04-16 1-888-543-4373...
- Page 6 Open the truck guard and tighten the bolts until they are snug. Figure 9.1 – Bracket and Lift Assist Reassembly e) Close the truck guard again to ensure the latches engage properly. Part No: KW22C4-02-IG 1-888-543-4373 Rev: B www.HERD.com Date: 2020-04-16 1-888-543-4373...
- Page 7 11. Install the air deflector (Item 9) to the truck guard (Item 1) as shown using the supplied hardware (Items 14, 15, 16). 23, 24 Figure 11 – Air Deflector Installation Part No: KW22C4-02-IG 1-888-543-4373 Rev: B www.HERD.com Date: 2020-04-16 1-888-543-4373...
- Page 8 Check mounting points after the first 5000 km and every 3-6 months. • This truck guard is equipped with Herd Slam Latch which requires periodic adjustment. Refer to Slam Latch Installation adjustment instructions (S001) to properly adjust your Slam Latch.
Need help?
Do you have a question about the KW22C4-02 and is the answer not in the manual?
Questions and answers