Table of Contents
Advertisement
TRAY ADJUSTMENTS
By re-timing the spirals, difficult-to-vend items can be dispensed more dependably. By altering tray spacing, larger items can be vended. By
changing the tray configuration, different product mixes can be accommodated
VERTICAL SPACING
The trays can be adjusted up or down in half-inch increments to provide additional headroom for vending taller products. When increasing
the height in one area, the same amount of room will be lost in the tray above or below the one being adjusted.
SNACK/CANDY/FOOD TRAY REMOVAL AND REPOSITIONING
1.
Pull out the tray to be adjusted until it stops.
2.
Disengage the tray harness from its retainer on the right side
wall. See Figure 12. Disconnect the tray plug from its receptacle
the harness retainer on the right sidewall.
3.
Lift up on the front of the tray and pull slightly (approximately
1.5 cm /.5 in) forward to clear the tray stop.
4.
Locate the release lever on the left and right tray rails. (See
Figure 13) Swing the release levers up to unlatch.
5.
Lift up on the rear of the tray and remove the tray from the
vendor.
6.
Remove the two tray rail mounting screws to remove both the
left and right tray rails from the left and right sidewalls. (See
Figure 13)
7.
Pull each rail forward to disengage its rear tab from the hole in
the rear wall.
8.
Relocate left and right rails by reversing step 6. Rails must be
level front to back and left to right.
9.
Place the tray rear rollers on the left and right rails and lifting up
on the front of the tray and push it back.
10. Swing the tray rail release levers all the way down (this guides
the tray for tilting when loading).
11. Re-install the tray plug into its receptacle on the right side wall.
12. Re-engage the tray harness into its harness retainer (See Figure
12).
Test-vend the tray in its new position to assure that the tray
13.
plug is properly seated.
CAN/BOTTLE TRAY REMOVAL
1.
Unlatch the tray and pull it all the way out until it stops.
2.
Disengage the tray harness from its harness retainer on the right side wall. See Figure 12. Disconnect the tray plug from its
receptacle on the right side wall.
3.
Remove and save the six (6) screws that fasten the tray to the left and right slides. Lift up and forward to remove the tray.
4.
Pull out on slides and remove and retain the screws fastening the slides to the side walls (See Figure 15).
5.
Relocate the slides and re-install with screws through the slides into the side walls. Assure slides are mounted level and in same
location from left to right and front to back.
6.
Reverse procedure to re-install tray.
7.
Test-vend the tray in its new position to assure that the tray plug is properly seated.
HIGH CAPACITY CAN TRAY REMOVAL
1.
Unlatch the tray and pull it all the way out until it stops.
2.
Disengage the tray harness from its harness retainer on the right side wall. See Figure 12. Disconnect the tray plug from its
receptacle on the right side wall.
3.
Remove and save the four (4) nuts located near the corners of underneath the tray. (See Figures 14a & b). Lift up and forward to
remove the tray.
4.
Pull out on slides and remove and retain the screws fastening the slides to the side walls.
5.
Relocate the slides and re-install with screws through the slides into the side walls. Assure slides are mounted level and in same
location from left to right and front to back.
S T / V T V E N D O R • 3 5 6 8 3 5 6 7 3 5 6 6 3 5 6 5 •
.
Figure 12. Tray Harness Connection
9
Figure 13. Tray Rails
4 2 2 0 5 5 7 R e v A
Advertisement
Table of Contents
