Table of Contents
Advertisement
INTRODUCTION
This manual contains instructions, service and installation guidelines for the Single Temp (ST) / Variable Temp (VT) Glass front Vendor.
Please read this manual thoroughly and follow the instructions. The initial set-up of a vendor is a very important step of insuring that the
equipment operates in a trouble-free manner.
The ST Vendor is a single zone temperature vendor. All trays are held to a consistent set temperature. The vendor will maintain as low as
36°F (2°C) throughout ... maintaining health safety for perishable products. The temperature and health safety settings can be adjusted
within the control system (see programming manual).
The VT Vendor is a two zone/two temperature vendor. This provides for two temperature zones (top and bottom) in a single vendor. The
zones are separated by a moveable air deflector and insulating barrier. The vendor has an air duct that runs up and down on the back
inner wall of the cabinet. For example: In a 5 tray configured vendor the air deflector and insulating barrier can be moved to provide a
refrigerated zone for the bottom two trays while providing a chilled top zone for the top three trays. Positioning of the air deflector and
insulating barrier is adjustable in a range of 2 trays in the bottom zone/ 4 trays in the top zone, 3 & 3, or 4 & 2 ... dependent upon product
height and tray spacing. The vendor will maintain 36°F (2°C) in the bottom zone while the top zone will be as high as 66°F (19°C)
depending upon ambient conditions. The top compartment can be optionally equipped with a heater & blower system along with a
separate temperature sensor & relay to maintain a constant and/or higher temperature across varying ambient temperatures.
Both vendors will operate within an ambient temperature range of 40°F-90°F (4°C-32°C).
The temperature setting for both compartments are set within the control system (see programming manual).
The bottom or single zone has a temperature sensor. The modular insulated refrigeration system draws air across the refrigeration system's
evaporator coils up the back air duct and circulates down through the trays. There are openings in the bottom trays to allow air to circulate
around the products.
All programming (pricing, vend functions and features) are also done within the control system. Changes can be made without any
additional accessories or remote parts. Selections can be priced individually from $00.00 to $655.35 in five cent increments (US currency).
Cash accountability records, total cash transactions, total vend cycles performed by the vendor, information for individual selections,
complete rows or total vendor can be compiled and used for inventory and ordering records. Electrical malfunctions are recorded and
displayed when the vendor is placed in the Service Mode. Non-functional motors or selections are indicated. Each selection has an
individual motor. Functional selections will continue to operate if other motors become nonfunctional.
The vending sequence is "first-in, first-out" for each selection, permitting stock rotation to maintain fresh products in the vending area.
Each ST / VT Glassfront Vendor has the capability of supporting up to two USD satellite vendors such as a Cold Food (CF-1000) or Frozen
Food (FF-2000). The satellite vendor utilizes the host vendor's control system, coin mechanism, bill validator and keypad to perform the
vend functions they require. For details on the satellite vendor, refer to the Service Manual pertaining to the specific vendor for installation
instructions. Satellite vendors may require optional kits for installation.
Access to the service area of this vendor should be permitted only to individuals having knowledge and practical experience in vendor setup
and loading, especially in areas of safety and hygiene.
SPECIFICATIONS
DIMENSIONS & WEIGHTS
Note:
ELECTRICAL
NOMINAL
AMPS
S T / V T V E N D O R • 3 5 6 8 3 5 6 7 3 5 6 6 3 5 6 5 •
TYPE
MODEL
3567/3568
WIDTH
DEPTH
HEIGHT
1
ESTIMATED WEIGHT
1
EST. SHIPPING WT.
1
Weights will vary depending on tray configuration and optional equipment installed.
HORSPOWER
VOLTAGE
CYCLE
HEATED GLASS
NON HEATED
GLASS
TRANSFORMER
ST/VT (3 WIDE)
3567A/3568A
3565/3566
29.5 in. (74.9 cm)
38 in. (96.5 cm)
72 in. (182.9 cm)
693 lbs (614 kg)
722 lbs (327 kg)
1/3 HP Embraco
115 VAC
60 Hz
6.5
5.5
110/24 VAC
4
ST/VT 5000 (5 WIDE)
3565A/3566A
41.2 in. (104.6 cm)
816 lbs (370 kg)
846 lbs (384 kg)
230 VAC
50 Hz
3.5
3.0
230/24 VAC
4 2 2 0 5 5 7 R E V A
Advertisement
Table of Contents
