Table of Contents
Advertisement
Quick Links
Important: Retain these instructions
Contents
1
Unpacking ........................................................................... 1
2
Storage ............................................................................... 1
1
Unpacking
2
Storing
-10 °C
(14 °F)
3
Installation
Dimensions
1
160 mm (6.3")
INC2 Installation Instructions TG200231 Issue 2, 22-Mar-2018
Internetwork Node Controller
J8
+50 °C
(122 °F)
33 mm
(1.38")
Installation Instructions
3
Installation
3.1 Installation - Mounting ......................................................... 1
3.2 Installation - Configuration ................................................. 4
4
Disposal .............................................................................. 8
ET1
J16
Dev B
J15
Dev A
J9
J7
Lan B
Lan A
0
95 %RH
It is recommended that the installation should
comply with the HSE Memorandum of Guidance
on Electricity at Work Regulations 1989.
For USA install equipment in accordance with the
National Electric Code.
WARNING: Opening the panel may expose dangerous
voltages.
417-IEC-5036
Caution: The INC2 contains static sensitive devices.
Suitable anti-static precautions should be
taken throughout this operation to prevent
damage to the unit.
BS EN100015/1 Basic Specification: protection of
electostatic sensitive devices.
INC2
Installation Instructions,
TG200231
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TREND INC2
Summary of Contents for TREND INC2
- Page 1 160 mm (6.3") WARNING: Opening the panel may expose dangerous voltages. 417-IEC-5036 Caution: The INC2 contains static sensitive devices. Suitable anti-static precautions should be taken throughout this operation to prevent damage to the unit. BS EN100015/1 Basic Specification: protection of electostatic sensitive devices.
- Page 2 Mount the Node The INC2 can be fitted into enclosures and controllers as shown in the table below: 151 mm (5.94") 4 off 4 mm * INC2 board fits with 3 screws in normal node position or fits in NDP position (if no NDP).
- Page 3 (unless RS232 receiver/transmitter Device B being used e.g. leased line modem) Always Internetwork terminal size 0.5 to 2.5 mm (14 to 20 AWG) Network Engineering Manual, 92-1735. LAN B / IWRK polarity independent 4 wire 2 wire LAN B / IWRK additional terminals INC2 Installation Instructions TG200231 Issue 2, 22-Mar-2018...
- Page 4 INC2 Installation Instructions 3.1 Installation - Mounting (Continued) Close Panel/Box INC2/USA: The unit is UL rated as 'UL916 accessory to open energy management equipment'. 3.2 Installation - Configuration WARNING: Opening the panel may expose Switch off and open panel/covers dangerous voltages.
- Page 5 2 devices (e.g. 3xtend/EINC L) Note: communicating over the internetwork. This baud = R2 = R2 needs rate is not supported through the LAN A terminals. extra link = R2 BAUD B BAUD A INC2 Installation Instructions TG200231 Issue 2, 22-Mar-2018...
- Page 6 LAN A Check network cabling INC2 Faulty for short circuits with a LAN A multimeter (NOT Megger) Check baud rate. Power up other nodes until faulty node is found (OK ). Correct fault. INC2 Installation Instructions TG200231 Issue 2, 22-Mar-2018...
- Page 7 Note that a PIN may be required to make changes in configuration mode. If the PIN has been forgotten the user should contact Trend Technical Support quoting the generator number (User module) whereupon a default PIN will be supplied. This will only work during the same configuration mode session i.e.
- Page 8 Division of Honeywell Technologies Sàrl, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.
Need help?
Do you have a question about the INC2 and is the answer not in the manual?
Questions and answers