Advertisement
Quick Links
Important: Retain these instructions
These instructions shall be used by trained service
personnel only.
If the equipment is used in a manner not
specifi ed by these instructions, the protection provided by the
equipment may be impaired.
CONTENTS
1
Before Starting Confi guration .......................................1
2
Confi guration . ................................................................1
1
BEFORE STARTING CONFIGURATION
Install the IQ422, IQ4NC/00, IQ4NC/12
IQ422, IQ4NC/00, IQ4NC/12 Installation
Instructions - Mounting (TG201264)
Prepare Ethernet Network
Install DHCP Server
If the IP address settings (IP address, subnet mask, default
router, WINS and DNS servers' addresses) are to be supplied
by a DHCP server, ensure one is installed on the Ethernet
segment to which the IQ422, IQ4NC/00, IQ4NC/12 is
connected.
Install WINS Server
If host names are being used for IP addressing across a
router, a WINS server must be installed.
Install DNS Server
If email alarms are being sent, and the email server address
is identifi ed by internet domain name, a DNS server must be
installed.
2
CONFIGURATION
Isolate All Power
1
O
I
IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018
InstallationInstructions-Confi guring
IQ422, IQ4NC/00, IQ4NC/12
(if using Ethernet)
(including any I/O supplies)
O
PSU
I
O
PSU
I
https://partners.trendcontrols.com
3
Connect to IQ4xx ........................................................10
4
Reset to Defaults . ........................................................12
InstallSETonPC/Laptop
SET Manual (TE200147)
Additional Documentation Required
▪
SET Manual (TE200147)
▪
IP Tool Manual (TE200638)
▪
IQTool Monitor Applet Manual (TE201298)
▪
IQTool Addresser Applet Manual (TE201299)
▪
IQ4 Confi guration Manual (TE201263)
Note: PDF copies are included with SET installation in the
following folder: C:\...\Trend Control Systems\Documentation
Read&AgreetoEndUserLicenceAgreement
IQ422, IQ4NC/00, IQ4NC/12 Installation
Instructions - Mounting (TG201264)
WARNING Connecting leads may be connected
to power supplies. Isolate before touching.
Controllers
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TREND IQ422
Summary of Contents for TREND IQ422
- Page 1 ▪ IQTool Monitor Applet Manual (TE201298) by a DHCP server, ensure one is installed on the Ethernet ▪ IQTool Addresser Applet Manual (TE201299) segment to which the IQ422, IQ4NC/00, IQ4NC/12 is ▪ IQ4 Confi guration Manual (TE201263) connected. Note: PDF copies are included with SET installation in the Install WINS Server following folder: C:\...\Trend Control Systems\Documentation...
- Page 2 WARNING Opening the panel may expose dangerous voltages. OpenRotatingCovers Disconnect All I/O Leave Power, Ethernet, Current loop LAN, USB, RS232, and MS/TP connected (where appropriate). Select Terminator Switch Position (IQ4NC using MS/TP network only) IQ422, IQ4NC/00, IQ4NC/12 Installation Instructions - Mounting (TG201264) for details of terminator use. Terminator in circuit Terminator out of circuit IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018 .
- Page 3 Note: All LEDs illuminate for several seconds after switch on. CheckPower&WatchdogIndicators Normal operation indication Power Watchdog Power Watchdog (green) (red) Fault indications Check input power supply Power Device fault. Try resetting the IQ4xx Watchdog to default settings (see page 12). Check Ethernet Indicators (if Ethernet is connected) Normal operation indication (green) (yellow) Fault indications Check Ethernet IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018...
- Page 4 IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Configuring CONFIGURATION (continued) Connect to the IQ4xx Using the PC/laptop (see step 7) run SET / IP Tool SET Manual (TE200147) IP Tool Manual (TE200638) Then find the IQ4NC, IQ422 by its MAC address as shown on serial label Q422B_V53440388 MAC Addr 00:10:70:0D:1E:92 Part No: IQ422-1010U5000 Addr SetupIPAddressingDetails (if using Ethernet) Use IP Tool – see step 12 – to choose either static (fixed) or IP Tool Manual (TE200638) dynamic (DHCP) addressing: Dynamic(DHCP)Addressing(default) When set to dynamic (DHCP) addressing the unit automatical Parameter Value obtains its IP addressing details (IP address, subnet mask,...
- Page 5 InstallationInstructions-Configuring IQ422, IQ4NC/00, IQ4NC/12 CONFIGURATION (continued) Set up IQ4NC Communication Mode (if using IQ4NC) Ethernet Internetwork to to MS/TP LAN (default) Parameter Notes ▪ Connect a PC directly to the IQ4 using an Ethernet cable, LAN number 1, 4 to 9, 11 to 119 see ‘Connect to IQ4’ on page 10. BACnet IP Can be disabled ▪ Using a web browser, e.g. Internet Explorer, access the controller’s web pages and select Modules>Networks to Current Loop Internetwork to MS/TP LAN display the NCConfigurationWizard. Parameter Notes LAN number 1, 4 to 9, 11 to 119...
- Page 6 IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Configuring CONFIGURATION (continued) Set up Ethernet Access Across Routers (if required) IP Tool Manual (TE200638) If the LAN is to be built across a router(s) details of devices (on each subnet) must be specified to enable cross-router It is recommended that at least two devices from each subnet communications. are specified. For increased reliability details of additional devices should be specified. Use IP Tool – see step 12 – to specify IP settings for up to 20...
- Page 7 InstallationInstructions-Configuring IQ422, IQ4NC/00, IQ4NC/12 CONFIGURATION (continued) SetCurrentLoopBaudRate (IQ4NC or ../LAN variants only, if current loop network being used) IQTool Monitor Applet Manual (TE201298) By default the IQ4xx will auto detect the baud rate in use on SET Manual (TE200147) the current loop. If all devices are set to auto detect the baud IQ4 Configuration Manual (TE201263) rate chosen cannot be guaranteed, in which case it may be necessary to manually set one device to a known rate. Use SET’s IQTool Monitor Applet to disable autobaud and specify the baud rate. Module Parameter Range IQ Lan...
- Page 8 Note: strategy download is not recommended over current loop with baud rate <9k6. Note: SET will set up the controller’s date and time to that of the PC during download. However, they may be set up from a controller confi gured as timemaster. Check IQ422 or IQ4NC on BACnet (If /BAC or IQ4NC and BACnet protocol communications required) Use SET to check that the IQ4 BACnet functionality is SET Manual (TE200147) operating by checking it appears correctly in the System View on its BACnet network.
- Page 9 IQ4 Confi guration Manual (TE201263) over Ethernet or the current loop. SET Manual (TE200147) BackupStrategy SET Manual (TE200147) Use SET to upload the strategy and compare it with the Note: An Ethernet connection is required to upload strategy strategy held by SET. and backdrop fi les. Other connection types only allow upload of strategy fi les. CloseRotatingCovers Close Panel / Enclosure IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018...
- Page 10 CABLE/EJ101442 RD/SDU-IQ2COMMSCABLE3M 9 way female RJ11 D type RJ11 RJ11 IQView8 Connection use Notes Note: If local supervisor port address is ‘0’ (default) IPTool communication is limited to the IQ4xx. If non-zero, ü communication is possible over the entire network. Web Browser Supervisor ü IQ422, IQ4NC/00, IQ4NC/12 Controllers Installation Instructions - Confi guring TG201265 Issue 12, 24-Jul-2018 .
- Page 11 ▪ Connect the other device (e.g. network display or PC) to same Ethernet network and ensure an IP connection is IQView8 available between it and the IQ4xx. ▪ To make a connection with SET, a supervisor or display ensure a vCNC is available in a Trend device on the same Ethernet Trend network and connect to the vCNC as described in the supplied documentation. Note: If connecting with IP Tool, the PC should be on the same Ethernet segment as the IQ4xx. RJ45 Standard Ethernet cable (Cat 5e twisted pair) ▪ To make a connection with a web browser run a web...
- Page 12 ON. This process may take up to 10 minutes depending on controller type. Do not switch off the controller until the process has completed. Re-confi gureController Go to step 1 on page 1. Please send any comments about this or any other Trend technical publication to techpubs@trendcontrols.com © 2018 Honeywell Products and Solutions SARL, Connected Building Division. All rights reserved. Manufactured for and on behalf of the Connected Building Division of Honeywell Products and Solutions SARL, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.
Need help?
Do you have a question about the IQ422 and is the answer not in the manual?
Questions and answers