Contact Information - Axis A1001 Installation Manual

Australia/New Zealand
This digital equipment fulfills the requirements for RF
emission according to the Class B limit of AS/NZS CISPR 22.
The product shall be connected using a shielded network
cable (STP) that is properly grounded.
-
Japan
この装置は、クラスB 情報技術装置です。こ
の装置 は、家庭環境で使用することを目的としてい
ます が、この装置がラジオやテレビジョン受信機に
近 接して使用されると、受信障害を引き起こすこと
があります。取扱説明書に従って正しい取り扱い
をして下さい。本製品は、シールドネットワーク
ケーブル(STP)を使用して接続してください。また
適切に接地してください。
Safety
This product complies with IEC/EN 60950-1, Safety of
Information Technology Equipment. If its connecting cables
are routed outdoors, the product shall be grounded either
through a shielded network cable (STP) or other appropriate
method.
The power supply used with this product shall fulfill the
requirements for Safety Extra Low Voltage (SELV) and
Limited Power Source (LPS) to IEC/EN/UL 60950-1.
Disposal and Recycling
Europe
This symbol means that the product shall not be
disposed of together with household or commercial
waste. Directive 2012/19/EU on waste electrical
and electronic equipment (WEEE) is applicable in
the European Union member states. To prevent
potential harm to human health and the environment, the
product must be disposed of in an approved and
environmentally safe recycling process. For information
about your nearest designated collection point, contact your
local authority responsible for waste disposal. Businesses
should contact the product supplier for information about
how to dispose of this product correctly. This product
complies with the requirements of Directive 2011/65/EU on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS).
China
This product complies with the requirements of the
legislative act Administration on the Control of
Pollution Caused by Electronic Information Products
(ACPEIP).

Contact Information

Axis Communications AB
Emdalavägen 14
223 69 Lund
Sweden
Tel: +46 46 272 18 00
Fax: +46 46 13 61 30
www.axis.com
Supported Readers
This list of supported readers is subject to change without
notice. Contact your Axis reseller for information about
supported readers.
This product is compatible with UL Listed Wiegand access
control readers.
This product is compatible with the following RS485 access
control readers:
AXIS A4011-E Reader
HID iCLASS® RW100: 6101CG40000, 6101CGM0000,
6101CK40000, 6101CK40002, 6101CK40100, 6101CK403C0,
6101CKM0000, 6101CKM0002, 6101CKM0203; RW300:
6111CG40000, 6111CG400C0, 6111CGM0000,
6111CK40000, 6111CK4000Z, 6111CKM0000; RW400:
6121CG40000, 6121CGM0000, 6121CK40000,
6121CK40003, 6121CK40007-G3.0, 6121CK4000D-G3.0,
6121CKM0000; R40: 6122CKP00P0, 6122CKP05P0,
6122CKP06P0; RWK400: 6131CG4020000,
6131CK4000000, 6131CK4000014, 6131CK4000300,
6131CK4020000, 6131CKM000000, 6131CKM000214;
RK40: 6132BKP00Q709-G3.0, 6132CKP000009,
6132CKP000011, 6132CKP000700-G3.0,
6132CKP000709-G3.0, 6132CKP001009, 6132CKP001011,
6132CKP00P000, 6132CKP00P009, 6132CKP00P709-G3.0,
6132CKP00Q709-G3.0, 6132CKP030014, 6132CKP060514,
6132CKP06P009, 6132CKP06P609, 6132CKP070209;
RW150: 6141CG40000, 6141CGM0000, 6141CK40000,
6141CKM0000; R15: 6142CKP000Z, 6142CKP00P0,
6142CKP0100; RWKL550: 6171BK4000000,
6171BK4000009, 6171BK4000014, 6171BK4000214,
6171BK4000500, 6171BK4040Z14, 6171BK4060000,
6171BK4060209, 6171BK4060Z09, 6171BK4061000,
6171BKM000000, 6171BKM000200, 6171BKM000300,
6171BKM040400; RWKLB575: 6181BK4000000,
6181BK4000009, 6181BK4000014, 6181BK4000022,
6181BK406C009
HID Smartid®: 8031DSAP
HID pivClass® R10-H: 900LHRNAK00000, 900LHRTAK00000,
900NHRNAK00000, 900NHRTAK00000, 900PHRNAK00000,
900PHRTAK00000, 910LHRNAK00000, 910LHRTAK00000,
910NHRNAK00000, 910NHRTAK00000, 910PHRNAK00000,
910PHRTAK00000, 920LHRNAK00000, 920LHRTAK00000,
920NHRNAK00000, 920NHRTAK00000, 920PHRNAK00000,
920PHRTAK00000, 921LHRNAK00000, 921LHRTAK00000,
921NHRNAK00000, 921NHRTAK00000, 921PHRNAK00000,
921PHRTAK00000; RPKCL40-P: 923LPRNAK00000,
923LPRTAK00000, 923NPRTAK00000, 923PPRNAK00000,
923PPRTAK00000
TM
: M11, MTK15, MTMSK15, MT15, MTMS15
Aptiq
For information about which compatible RS485 access
control readers have been verified by UL, see Requirements
for compliance with on page 3.
Requirements for compliance with
th
UL294 6 edition
This section contains information and instructions required
for UL compliance. To make sure the installation is UL
compliant, follow the instructions below in addition to the
general information and instructions provided throughout
this document. In cases where pieces of information
contradict each other, the requirements for UL compliance
always replace general information and instructions.
Supported Readers
• Compatibility with the following RS485 readers has been
verified by UL: HID iClass RK40, HID SmartID 8031 DSHM,
and AptiqQ MTMSK15.
Safety Instructions
• The Axis product shall be installed and serviced by a factory
trained professional.
• The Axis product shall be installed within the protected
premises (secured area).
• The Axis product shall be mounted indoors. Outdoor use
has not been evaluated or approved by UL.
• All interconnecting devices shall be UL Listed and Class 2
low-voltage power limited.
• All wiring methods shall be performed in accordance with
NFPA70, local codes and authorities having jurisdiction.
• When the Axis product has reached the end of its useful
life, dispose of it according to local laws and regulations.
The product should not be disposed of together with
household or commercial waste. See Disposal and
Recycling on page 3.