Related Manuals for Fisher Scientific Isotemp 642
Summary of Contents for Fisher Scientific Isotemp 642
- Page 1 Isotemp Hybridization Incubators Installation and Operation Manual 103751 Rev. 2 © 2010 Fisher Scientific Inc. All rights reserved Printed in U.S.A.
- Page 2 100V 13-247-22Q Medium 230V 13-247-30Q Dual 120V 13-247-31Q Dual 100V MANUAL NUMBER 103751 (7000621) 40460 9/9/15 Removed CE references 31325 2/13/15 Added explosion and fire cautions 5/13/10 Transfer to Marietta (was 103751 10/4/06) ECR/ECN DATE DESCRIPTION Fisher Scientific Hybridization Incubators...
- Page 3 Fisher Scientific makes no representations or warranties with respect to this manual. In no event shall Fisher Scientific be held liable for any damages, direct or incidental, arising out of or related to the use of this manual.
- Page 4 EU Member State European Country, and this product should be disposed of or recycled through them. Further information on Fisher Scientific’s compliance with this directive, the recyclers in your country and information on these products will be available at www.fishersci.com.
- Page 5 When more extensive service is necessary, we will assist you with direct factory trained technicians or a qualified service organization for on-the-spot repair. If your service need is covered by the Fisher Scientific Products warranty, we will arrange for the unit to be repaired at our expense and to your satisfaction.
-
Page 6: Table Of Contents
Unloading the Rocker ........5-11 Fisher Scientific Hybridization Incubators... - Page 7 Accessories ..........9-1 Hybridization Incubators Fisher Scientific...
-
Page 8: Introduction
Introduction Section 1 This manual provides information and procedures on how to unpack, set up, and operate the Fisher Scientific Isotemp brand of Hybridization Incubators. This manual is intended to be used by Fisher customers responsible for operating the hybridization incubator. -
Page 9: Rotisseries Available
The dual unit, accepts two rotisseries, identical to those describe for use in the medium unit. As an alternative to rotisseries, a rocker is available for agitating samples. The rocker is an option on the medium and dual units and it replaces the rotisserie. Hybridization Incubators Fisher Scientific... -
Page 10: General Specifications
Medium: ..... . .55 lbs (25 kg) Dual: ......105 lbs (48 kg) Fisher Scientific Hybridization Incubators... -
Page 12: Safety Information
(see above). Note The red bar to the left of the display indicates a negative value. Used in calibrating the unit. Indicates that the unit is operating in the alarm condition ALARM Alarm (the indication is only seen during the alarm condition). Fisher Scientific Hybridization Incubators... - Page 13 • Do not continue to use the incubator if the temperature controller fails, as evidenced by the red ALARM indicator lighting. • Use appropriate hand and eye protection when handling hazardous chemicals. Hybridization Incubators Fisher Scientific...
- Page 14 Tilt incubator to allow grasping under bottom of unit at the sides or back. Do not lift by grasping under plastic bezel at front of unit. Dual unit may require a third person to prevent unit from tipping while being moved. Fisher Scientific Hybridization Incubators...
-
Page 16: Unpacking And Installation
Small Medium Dual Item supplied Hybridization incubator Drip tray Rotisserie 35mm x 150mm hybridization tube (Cat. No. 13-247-150) 35mm x 300mm hybridization tube (Cat. No. 13-247-300) Spare tube clips Power cord Instructions Warranty card Wall Bracket Fisher Scientific Hybridization Incubators... -
Page 17: Installation Procedure
5. Install drip tray inside incubator Wall bracket chamber. Wall 6. Plug the power cord into a suitable grounded electrical outlet. 7. Check out system operation before using unit. 8. Complete and return warranty Figure 4-1. Wall Bracket card. Hybridization Incubators Fisher Scientific... -
Page 18: Operation
Shows messages to indicate Use in conjunction with menu menu functions. key to access other functions. Take action depending on Shows status and error mes- message. (See Power Up sages. Messages) Fisher Scientific Hybridization Incubators... -
Page 19: Rear Panel Nomenclature
Plug mating end of power power entry module/ power to unit. Filters incoming and cord into this connector. Plug line filter/fuse holder outgoing power line noise. Holds fuses other end into suitable power for over-current protection. outlet. Hybridization Incubators Fisher Scientific... -
Page 20: Power Up
1. Set the power switch to the I position. Display alternates between oFF and the measured temperature. If you get any other message, see “Power Up Messages” below. 2. Press any key to stop the oFF display. The system displays the actual temperature inside the incubator. Fisher Scientific Hybridization Incubators... -
Page 21: Setting The Temperature
0.0 and 85.0°C. 3. Release the arrow keys when the temperature is set as desired. After ten seconds, the display shows the actual temperature. To return to the actual temperature immediately, press the menu key. Hybridization Incubators Fisher Scientific... -
Page 22: Setting Offset Temperature
3. Press and hold either the up or down arrow key to set the desired offset. In the example above, you would set the offset to -3.0°C. 4. Check the temperature accuracy again and change the offset as necessary to achieve the desired temperature. Fisher Scientific Hybridization Incubators... -
Page 23: Reading / Resetting Temp Deviation
Display shows temperature deviation of 0.0. After ten seconds, the display returns to the actual temperature. To return to the actual temperature immediately, press the menu key. Hybridization Incubators Fisher Scientific... -
Page 24: Installing The Rotisserie Into The Incubator
4. Line up the right side of the shaft with the gear drive socket, as shown in Figure 5-4. Release the rotisserie and allow the shaft to be pushed into the socket. Figure 5-4. Drive Socket Fisher Scientific Hybridization Incubators... -
Page 25: Loading The Rotisserie
7. Close the incubator door, set the temperature, and set the rotisserie motor switch on to start processing. 8. At the conclusion of processing, set the power switch off, open the incubator door, and unload the rotisserie. Hybridization Incubators Fisher Scientific... -
Page 26: Setting The Rotisserie For Variable Axis
4. Tighten the screws so the rotisserie does not twist. 5. Install the rotisserie into the incubator. Figure 5-5. Screw Locations screws screws screws Figure 5-6. Small Incubator Screw Locations Fisher Scientific Hybridization Incubators... -
Page 27: Unloading The Rotisserie
3. Place the rocker in the incubator and secure it to the back of the incubator with the two existing screws from the back panel, as Figure 5-7. Rocker Installation shown in Figure 5-7. 5-10 Hybridization Incubators Fisher Scientific... -
Page 28: Loading The Rocker
2. Use the rotisserie motor switch to jog the rocker if necessary to assist in removing samples. 3. Set the power switch off. 4. Clean the unit in preparation for the next use. Fisher Scientific Hybridization Incubators 5-11... -
Page 30: Maintenance
Where there is a heavy coating of residue on the stainless surfaces, or where there is evidence that corrosion is beginning, use a stainless steel cleaner. • Rinse and wipe all surfaces with clean water and allow to air dry. Fisher Scientific Hybridization Incubators... -
Page 32: Service
Display alternates between actual Temperature setting has been reduced below current temperature and Alr (alarm). chamber temperature. Defective solid-state relay. Defective thermocouple; defective temperature con- ALARM light on troller board; defective solid state relay, defective safety thermostat. Fisher Scientific Hybridization Incubators... -
Page 33: Replacement Parts
SPN40521 Power cord, Euro SPN83115 Power cord, UK SPN83117 Door gasket SPN103967 Front panel overlay, with “wave” SPN103974 Front panel overlay, no “wave” SPN103975 Rotisserie tube clip, 35 mm SPN103958 Rotisserie tube clip, 70 m SPN104008 Hybridization Incubators Fisher Scientific... -
Page 34: Tightening Loose Belt Tension
4. Using a 11/32 nut driver, loosen the two nuts that hold motor bracket to the chassis. 5. Slide the motor to the rear to tighten belt tension, then tighten nuts. 6. Replace chassis bottom. Fisher Scientific Hybridization Incubators... - Page 35 4. Using a 11/32 nut driver, loosen the two nuts that hold motor bracket to the chassis. 5. Slide the motor to the rear to tighten belt tension, then tighten nuts. 6. Replace chassis back cover. Hybridization Incubators Fisher Scientific...
-
Page 36: Chemical Bioreagents
20 liter BP1333-20 Tris Borate EDTA, 1X Solution (TBE) 20 liter BP2430-20 500 ml BP1332-500 Tris Acetate EDTA, 50X Solution (TAE) 1 liter BP1332-1 20 liter BP1332-20 Tris Acetate EDTA, 1X Solution (TAE) 20 liter BP2434-20 Fisher Scientific Hybridization Incubators... -
Page 38: Accessories
(available in pack of 2 or case of 6) Hybridization tube cap O-ring 13-247-RNG Rotisserie, 35 mm, 4/8 tubes 13-247-15 Rotisserie, 70 mm, 2 tubes 13-247-16 Rotisserie, 35 mm, 10/20 tubes 13-247-25 Rotisserie, 70 mm, 4 tubes 13-247-26 Fisher Scientific Hybridization Incubators... - Page 40 For customer service, call 1-800-766-7000 To fax an order, use 1-800-926-1166 To order online: www.fishersci.com...