Using The Electronic Timer; Using The Electronic Timer With Push Knob - Bompani BO243OH/E Instructions For Use And Maintenance Manual

GB
used manually.
"+" AND "-" BUTTONS
- Pressing the "+" or "- "buttons makes time go up or down at
variable speed according to how long the button is pressed for.
MANUAL USE
- Press the MANUAL button: the AUTO symbol goes out (if
flashing or permanently on) the SAUCEPAN symbol lights up
and the oven can be used by adjusting the thermostat knob
and the selector switch according to the instructions given in
the manual.
AUTOMATIC OPERATION WITH END OF COOKING AND
DURATION TIMERS
- Let's use an example: it is 9:25 am; you want the oven to switch
on at 11 am and switch off at 12 pm (cooking time 1 hour).
- Press the COOKING DURATION button and within 5 seconds
press "+" button until it shows 01.00, adjust using "-" button if
necessary. The AUTO and PAN symbols come on permanently.
- Press the END OF COOKING button and within 5 seconds
press "+" button until it shows 12.00. The PAN symbol goes
out but the AUTO symbol remains permanently on.
- Move the oven thermostat knob to the desired temperature,
and the selector switch to the required cooking method; the red
warning light comes on the oven light comes on and the timer
is ready to start: at 11am the oven will come on automatically
and the PAN symbol will light up.
- When cooking is over (12 am) the AUTO symbol flashes, the
PAN symbol goes out and a buzzer sounds; to turn off the
buzzer press any button.
- Move the thermostat and selector knob to the OFF position.
SEMI-AUTOMATIC OPERATION WITH COOKING DURATION
SELECTION
- Let's take an example: it is 11:35 am and you want the oven
to stay on for 25 minutes from now on.
- Press the COOKING DURATION button and within 5 seconds
press the "+" button until it shows 00.25, adjusting the time with
the "-" button if necessary. The AUTO and PAN symbols light
up permanently.
- Turn the oven thermostat knob to the desired temperature
and the selector switch to the required cooking method; the
red warning light comes on, the oven light comes on and the
oven starts to operate.
- After 25 minutes the oven and the PAN symbol go out. The
AUTO symbol flashes and the buzzer tells you that cooking is
over: to turn off the buzzer press any button.
- Then move the oven thermostat knob and the selector switch
to the OFF position.
MINUTE MINDER
- Press the MINUTE MINDER button and choose the desired
time using the "+" or "-" button.
- The BELL symbol lights up when the minute minder is in use.
- When the pre-set time is over, the buzzer sounds and the
BELL symbol goes out.
BUZZER
- The buzzer sounds at the end of a programme and lasts for a
maximum of 7 minutes.
- To turn it off, press any button.
- Pressing the "-" button without having previously selected a
function the frequency of the signal changes. A selection from
3 possibilities can be made. The selected signal is audible as
long as the "-" button is pressed.
STARTING AND CHECKING A PROGRAMME
- The programme starts after about 4 seconds of it being set.
- The set programme can be checked at any point by pushing
the corresponding buttons.
PROGRAMMING ERRORS
- Example: at 12:15 pm a COOKING DURATION time of 30
minutes is set and a END OF COOKING is programmed in at
12:30 pm.
- The programme error can be rectified by changing the duration
or the end of cooking time, or by pressing the MANUAL button
and programming again.
- If there is a programming error the oven will not come on.
ANNULLING A PROGRAMME
- A programme can be cancelled by pressing the COOKING
DURATION button and then the "-" button until the display
shows 0.00.
IMPORTANT:
AT THE END OF EVERY PROGRAMMED COOKING OPERA-
TION YOU ARE ADVISED TO PRESS THE
ERWISE THE OVEN CANNOT BE OPERATED MANUALLY.
THREE -KEY ELECTRONIC TIMER (FiG. 8)
Allows programming of the duration of cooking in the oven.
If the cooking procedure does not require monitoring, it can also
take place in the user's absence.
AT POWER ON
When the appliance is powered up, the display flashes and the
time starts from "00:00". The oven is switched off. The display
flashes until the setting is made with "MODE".
SETTING THE TIME
On installation or after a power blackout, the display flashes.
The current time now has to be set.
Press the "MODE" key.
Press the.▲ or ▼.keys to set the current time.
MANUAL OPERATION
After the correct time has been set, the oven can be used in
manual mode with the aid of the oven thermostat knobs and the
selector switch (pan symbol on).
SEMIAUTOMATIC OPERATION WITH COOKING DURATION
In this operating mode, the user sets the cooking duration: at the
end of the countdown the oven switches off and a buzzer sounds.
Example: it is 11:35 and you wish the oven to stay on for 25
minutes starting from now. Press the ▲ key until the display
shows "25:00", adjusting the value if necessary with the ▼.key.
The pan and "auto" symbols are on. Turn the oven thermostat
knob to the temperature required and set the selector switch on
the chosen cooking mode: the oven indicator lights and inside
light illuminate and the oven comes into operation.
N.B.: To reset the cooking duration keep the ▼ key pressed
until zero is reached.
After 25 minutes the oven and the pan and "auto" symbols turn
off and the buzzer warns that the cooking procedure has ended.
Press the "MODE" key to stop the buzzer and restore manual
operation. Then turn the thermostat knobs and oven selector
switch to the off position.
N.B.: The units of measurement used for the cooking duration
change depending on the setting: initially the numbers on the
display show the minutes and the seconds, and increases are
in 10 seconds, until 99 minutes is reached.
DELETING PROGRAMS
Programmed cooking duration times can be deleted by pressing
the ▲ and ▼.keys simultaneously and releasing the ▲ key first.
USE OF SINGLE-CONTROL END OF COOKING TIMER
(WITHOUT CLOCK) (FIG. 9)
This allows the cooking time to be programmed. Operation:
- Move the knob to the desired cooking time (120 mins max.).
- Choose the temperature using the thermostat knob and move
the selector knob to the required cooking method.
- When the programming knob is at the 0 position the oven will
switch itself off. This is automatic.
- Move the thermostat knob back to symbol .
- Move the selector knob to symbol 0..
N.B. If the timer is not used, the oven programming knob is to
be set to the manual position

USING THE ELECTRONIC TIMER WITH PUSH KNOB

(FIG.10)
GENERAL OPERATION
This timer governs the time display (with analog hands) and the
30
For the user
BUTTON, OTH-
.