Advertisement
Wiring diagrams
Cooling (default ) operation
By default, the TF115P-002 is wired as a cooling control (see Fig. 3).
Figure 3.
TF115P-002.
Wiring for
GROUNDED
COOLING.
SERIES PLUG
Heating operation
▲
!
• Warning: disconnect power before changing wiring.
To change the operation from a cooling control to a heating control, proceed with the
following steps.
Figure 4.
TF115P-002
Junction Box
removed.
1.
Remove TF115P plug from the outlet to disconnect power.
2.
Unscrew four screws and remove the junction box cover (see Fig. 4).
3.
Disconnect the blue and white wires by removing the wirenut.
4.
Connect the red and white wires together with the wirenut (see Fig. 5).
Figure 5.
GROUNDED
TF115P-002.
SERIES PLUG
Wiring for
HEATING
5.
Twist the wirenut on the blue wire only.
6.
Re-install the junction box cover and tighten four screws.
▲
to ensure Water tigHtness, tHe gasKet must Be re-installed under tHe
junCtion Box Cover.
© COPYRIGHT 2012 PECO, INC. ALL RIGHTS RESERVED.
PECO is a registered trademark of PECO, Inc. All other trademarks, and/or registered trademarks, are the property of their respective owners.
COOLING
THERMOSTAT
ENCLOSURE
BLACK
BLACK
GREEN
GREEN
STAT
GRND
WHITE
BLUE
RED
HEATING
THERMOSTAT
ENCLOSURE
BLACK
BLACK
GREEN
GREEN
STAT
GRND
WHITE
BLUE
RED
Warning
!
limited WarrantY
1. WARRANTY COVERAGE. PECO Automation and Controls warrants to the original
user of its products that the products will, at the date of initial purchase, meet the
applicable specification for such products and will be free from any defects in materials or
manufacture under normal use for 18 months after date of manufacture.
2. DISCLAIMER OF WARRANTY OF PRODUCT SUITABILITY. PECO Automation and
Controls makes no warranty to the purchaser or any third party that its products are
suitable for a particular application or design. Many states and localities have differing
codes or regulations governing the installation and/or use of PECO Automation and
Controls' products. PECO Automation and Controls cannot guarantee compliance with
such regulations; purchaser is solely responsible for safe and correct installation and use
of the product and for compliance with applicable codes and regulations.
3. EXCLUSION OF IMPLIED WARRANTIES. This warranty is the only warranty
applicable to this product and excludes all other warranties, including any WARRANTY
OF MERCHANTABILITY, any warranty of fitness for a particular purpose, and any implied
warranties otherwise arising from course of dealing or usage of trade, except where the
product purchased is subject to consumer product warranty laws, in which case ANY
APPLICABLE IMPLIED WARRANTIES ARE LIMITED TO 18 MONTHS, or such shorter
period as permitted or required under applicable law. Some States do not allow limitations
on how long an implied warranty lasts, so the above limitations may not apply to you.
4. REMEDIES FOR NONCONFORMITY. If the product purchased does not conform to
the applicable warranty, PECO Automation and Controls will provide, at its option and in
accordance with the procedures in the following section, one of the following remedies:
(1) repair of the nonconforming product, (2) replacement with a conforming product, (3)
refund of the original purchase price. THESE REMEDIES SHALL BE THE EXCLUSIVE
AND SOLE REMEDY for any breach of warranty.
5. TO OBTAIN WARRANTY SERVICE. For any product believed to be defective within
the limited warranty period, first write or call dealer from whom product was purchased.
Dealer will give additional directions. If unable to resolve satisfactorily, write to PECO
Automation and Controls at the address below, giving dealer's name, address, date and
number of dealer's invoice, and describe the nature of the defect.
6. LIMITATION OF LIABILITY. PECO Automation and Controls WILL NOT BE LIABLE
FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES
resulting from any defect in the product purchased. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from State to State.
Manufactured by PECO Mfg. Co., Inc.
4784 SE 17th Avenue - Portland, OR 97202 - USA
P.O. Box 82189 - Portland, OR 97282 - USA
(PECO Automation and Controls is a division of PECO Mfg. Co., Inc.)
Note: Even though this thermostat is sealed, water or dust may enter through improperly
sealed wiring. The cover must be tightened securely to compress the gasket and provide
a watertight seal. Use only screws provided. Do not over-tighten.
2
P/N 70774 3220-2311 REV 00
Advertisement
