Advertisement
Quick Links
Advertisement
Related Manuals for VORON VORON 2.4 KIT 4
Summary of Contents for VORON VORON 2.4 KIT 4
- Page 1 VORON 2.4 KIT 4 ∙A / B DRIVE...
- Page 2 INTRODUCTION WWW.VORONDESIGN.COM Before you begin on your journey, a word of caution. In the comfort of your own home you are about to assemble a robot. This machine can maim, burn, and electrocute you if you are not careful. Please do not become the first VORON fatality.
- Page 3 A/B DRIVES AND IDLERS WWW.VORONDESIGN.COM...
- Page 4 OVERVIEW WWW.VORONDESIGN.COM B Drive A Drive B Idler A Idler...
- Page 5 PREPARATION WWW.VORONDESIGN.COM Heat Set Insert M5 Nut...
- Page 6 A IDLER WWW.VORONDESIGN.COM M5 Shim F695 Bearing ASSEMBLY AID This bolt is used to align components and will be removed in a later step. M5x40 SHCS...
- Page 7 A IDLER WWW.VORONDESIGN.COM M5x40 SHCS REMOVE ASSEMBLY AID Remove the bolt and slide the tension arm into place.
- Page 8 A IDLER WWW.VORONDESIGN.COM M3 Washer M3x40 SHCS...
- Page 9 A IDLER WWW.VORONDESIGN.COM CHECK YOUR WORK Compare your assembled parts to the graphics shown here. Pay attention to the features highlighted by the circles.
- Page 10 B IDLER WWW.VORONDESIGN.COM F695 Bearing M5 Shim ASSEMBLY AID This bolt is used to align components and will be removed in a later step. M5x40 SHCS...
- Page 11 B IDLER WWW.VORONDESIGN.COM M5x40 SHCS REMOVE ASSEMBLY AID Remove the bolt and slide the tension arm into place.
- Page 12 B IDLER WWW.VORONDESIGN.COM M3 Washer M3x40 SHCS...
- Page 13 B IDLER WWW.VORONDESIGN.COM CHECK YOUR WORK Compare your assembled parts to the graphics shown here. Pay attention to the features highlighted by the circles.
- Page 14 A DRIVE WWW.VORONDESIGN.COM M5x30 BHCS CUTOUT The printed parts for the A drive have a cutout.
- Page 15 A DRIVE WWW.VORONDESIGN.COM M5 Shim F695 Bearing UPSIDE DOWN ASSEMBLY For ease of assembly we recommend to assemble the A and B drives upside down. DON’T OVER TIGHTEN The M5 bolts are threaded directly into plastic.
- Page 16 A DRIVE WWW.VORONDESIGN.COM GT2 20 Tooth Pulley APPLY THREAD LOCKER Make sure to use thread locker on the set screws. MOTOR ORIENTATION Pay attention to the orientation of the cable exit. The wires from the motors will be pointing towards each other once fully assembled.
- Page 17 A DRIVE WWW.VORONDESIGN.COM M3x30 SHCS CHECK YOUR WORK Compare your assembled part to the graphic shown here. Pay attention to the pulley orientation and alignment with the bearing stack ups.
- Page 18 B DRIVE WWW.VORONDESIGN.COM M5x30 BHCS...
- Page 19 B DRIVE WWW.VORONDESIGN.COM M5 Shim F695 Bearing UPSIDE DOWN ASSEMBLY For ease of assembly we recommend to assemble the A and B drives upside down. DON’T OVER TIGHTEN The M5 bolts are threaded directly into plastic.
- Page 20 B DRIVE WWW.VORONDESIGN.COM GT2 20 Tooth Pulley APPLY THREAD LOCKER Make sure to use thread locker on the set screws. MOTOR ORIENTATION Pay attention to the orientation of the cable exit.
- Page 21 B DRIVE WWW.VORONDESIGN.COM M3x30 SHCS CHECK YOUR WORK Compare your assembled part to the graphic shown here. Pay attention to the pulley orientation and alignment with the bearing stack ups.
Need help?
Do you have a question about the VORON 2.4 KIT 4 and is the answer not in the manual?
Questions and answers