Table of Contents
Advertisement
Quick Links
TriStar Pump Series & HCP Commercial Series
The Hayward TriStar Pump is Specifically Engineered for the demanding requirements of today's in-ground
swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The
TriStar is a self-priming pump that incorporates an improved seal and impeller design that will provide many
years of efficient, dependable, corrosion-free service. The advanced design provides superior performance
while reducing maintenance requirements. NOTE - To prevent potential injury and to avoid unnecessary
service calls, read this manual carefully and completely.
IMPORTANT - READ CAREFULLY
NOTE
- The TriStar is a high performance, high efficiency
pump. When replacing most existing pumps, you can use a
TriStar pump with a lower horsepower rating than the
existing pump. Required: 2" Plumbing minimum.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
SAVE THIS INSTRUCTION MANUAL
HAYWARD POOL PRODUCTS CANADA INC.
2880 Plymouth Drive, Oakville, ON L6H 5R4
1.888.238.7665
Haywardpool.ca
P/N-IS3200-HC-12
Advertisement
Table of Contents
Related Manuals for Hayward TriStar Series
Summary of Contents for Hayward TriStar Series
- Page 1 INSTALLATION, OPERATION, & PARTS TriStar Pump Series & HCP Commercial Series The Hayward TriStar Pump is Specifically Engineered for the demanding requirements of today’s in-ground swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The TriStar is a self-priming pump that incorporates an improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service.
-
Page 2: Important Safety Instructions
CAUTION -- A Licensed electrician MUST complete, in full, all electrical installations noted in this manual. Use of non-Hayward replacement parts voids warranty. ATTENTION INSTALLER - THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT. - Page 3 - In addition to two or more suction outlets per pump installed in accordance with the latest IAF (formerly NSPI) standards and CPSC guidelines, follow all national, state, and local codes applicable. - Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
-
Page 4: Product Specifications
80 [300] 10” 3” [90] 160 [600] 15” NOTE - It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the pump suction inlet and any plumbing fittings. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... -
Page 5: Motor Specifications
208 - 230 12.4 - 11.2 ³ ¹ ² ¹, ², ³ Low Speed Amps: (¹ 2.8 - 3.0) (² 3.2 - 3.4) (³ 3.8 - 4.1) Three-Phase (3Φ) Pump - motor starter required USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... - Page 6 2.4 ( 1.79) 1.5 ( 1.12) 208-230/460 6.8-7.0/3.5 HCP322063 2.8 ( 2.09) 2 ( 1.49) 1.35 208-230/460 8.0-8.4/4.2 HCP323063 3.6 ( 2.68) 3 ( 2.24) 208-230/460 10.8-11.4/5.7 HCP325063 5 ( 3.73) 5 ( 3.73) 208-230/460 13.4-13.4/6.7 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
-
Page 7: Replacement Parts
SPX3200DLS Strainer Cover Kit (Includes Strainer Lexan Cover, Lock Ring, O-Ring) SPX3200S Strainer Cover O-Ring SPX3200M Strainer Basket SPX3200Z8 Diffuser Screw SPX4000Z1 Diffuser O-Ring SPX3200B3 Diffuser, 3 HP SPX3200Z1 Impeller Screw SPX3021R Impeller Ring USE ONLY HAYWARD GENUINE REPLACEMENT PARTS... - Page 8 HCPX3250Z1DC SPX3230C5 208-230/460 Commercial Pumps, 3 Phase Model No. Motor P/N Impeller P/N HCP320563 HCXP3205Z1D SPX3205C HCP320763 HCXP3207Z1D SPX3207C HCP321063 HCXP3210Z1D SPX3210C HCP321563 HCXP3215Z1D SPX3215C HCP322063 HCXP3220Z1D SPX3220C HCP323063 HCXP3230Z1D SPX3230C HCP325063 HCXP3250Z1D SPX3230C5 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...