Download Print this page
H3C PSR2400-12AHAH-B User Manual
H3C PSR2400-12AHAH-B User Manual

H3C PSR2400-12AHAH-B User Manual

Power module

Advertisement

Quick Links

H3C PSR2400-12AHAH-B Power Module User
Manual-5PW100
H3C PSR2400-12AHAH-B 电源手册-5PW100
Overview 简介
The PSR2400-12AHAH-B is a DC output power module that supports AC
and HVDC power input. It provides a maximum output of 2400 W. The
power module has two power inputs: primary power input (input 1) and
secondary power input (input 2). Only input 1 works if you connect power
to both power inputs. PSR2400-12AHAH-B 是一款提供直流输出的电源模
块,既支持交流输入也支持高压直流输入。这款电源模块的最大输出功
率可达 2400W。该电源有两路输入,Input 1 为主用输入,Input 2 为备用
输入,两路同时供电时负载在 Input 1。
The PSR2400-12AHAH-B power module exhausts air from its faceplate.
The following figure shows the PSR2400-12AHAH-B power module.
PSR2400-12AHAH-B 的风道风向是电源面板侧出风。下图展示
PSR2400-12AHAH-B 的外观。
1
BOM: 3101A13R

Advertisement

loading
Need help?

Need help?

Do you have a question about the PSR2400-12AHAH-B and is the answer not in the manual?

Questions and answers

Summary of Contents for H3C PSR2400-12AHAH-B

  • Page 1 BOM: 3101A13R Overview 简介 • The PSR2400-12AHAH-B is a DC output power module that supports AC and HVDC power input. It provides a maximum output of 2400 W. The power module has two power inputs: primary power input (input 1) and secondary power input (input 2).
  • Page 2 • The PSR2400-12AHAH-B power module is applicable to multiple switch models. The applicable switch models might change over time. For compatibility of the power module with switch models, contact the marketing personnel or technical support. PSR2400-12AHAH-B 适用于多 款交换机产品,其适用机型的准确信息随着时间变化有更新的可能性, 若您需要详细的适配信息,请咨询市场人员或技术支持人员。 •...
  • Page 3 • Connect the power cord to the external power supply system. 最后连接电源线至外置电源系统。 Technical specifications 电源模块规格 Item 项目 Specifications 规格 Rated input voltage range 100 to 240 VAC @ 50/60 Hz 额定输入电压范围 AC input Max input voltage range 90 to 290 VAC @ 47 to 63 Hz 交流输入...
  • Page 4 LEDs 电源模块状态指示灯 The PSR2400-12AHAH-B power module provides three LEDs on its faceplate to indicate the power input and output status. PSR2400-12AHAH-B 电源模块面板上 有三个电源模块指示灯,用于指示电源的输入、输出状态。 LED 指示灯 Mark 面板标示 Status 状态 Description 含义 Steady green Normal power output. 绿色常亮 输出正常 Abnormal power output.
  • Page 5 To avoid bodily injury, do not touch any bare wire or terminal. 不要接触露出的任何导线、端子部分,以免对人体造成伤害。 • To avoid power module damage, do not open the power module. When the internal circuits or components of the power module fail, contact H3C Support. 为了防止电源模块受损,请不要随意打开电源模块外壳,当电源模块内部 线路或元器件出现故障时,请移交维修人员进行检修。...
  • Page 6 2. Tools 工具准备 An ESD wrist strap is required for installing and removing the power module and connecting the power cord. Prepare an ESD wrist strap yourself. 安装和拆卸电源模块和电源线过程中需要使用防静电腕带,请用户自备。 3. Installing the power module 安装电源模块 • To prevent damage to the power module or the connector on the backplane of the powered device, insert the power module gently.
  • Page 7 (1) Use a screwdriver to loosen the captive screw on the power module slot adapter. 安装电源模块前,请先拆卸电源转接滑道,逆时针方向旋转螺丝刀, 拧松松不脱螺钉。 (2) Hold the power module slot adapter with your right thumb pressing the front panel and other fingers put into the hole.用右手大拇指顶住电源转接滑道的前 面板,其他手指抠住电源转接滑道侧面的凹槽。 (3) Pull the power module slot adapter part way out of the slot, and then pull it rightwards until the tabs on its left side disengage the chassis.
  • Page 8 (4) Unpack the power module and verify that the input mode of the power module is as required. 从电源模块包装盒中取出电源模块,确认电源模块的输入方式 与所需一致。 (5) Correctly orient the power module (with the latch below the handle). Grasping the power module handle with one hand and supporting its bottom with the other, slide the power module slowly along the guide rails into the slot.
  • Page 9 (1) Connect the female connectors of the two power cords to power input1 and power input2 on the power module, respectively. 将两根电源线带插孔的一端 分别插到电源模块的输入插口 1 和电源模块的输入插口 2 上。 (2) Use two releasable cable ties to secure the power cords to the handle of the power module, respectively.
  • Page 10 用一只手握住电源模块拉手,另一只手托住电源模块下方,将电源模块沿着插 槽导轨水平缓慢地拉出。 (5) Put the removed power module into an antistatic bag. 将拆卸下来的电源模块 放到防静电袋中。 Copyright © 2022, New H3C Technologies Co., Ltd. The information in this document is subject to change without notice. Copyright © 2022 新华三技术有限公司 版权所有,保留一切权利 本文档中的信息如有更改,恕不另行通知 如需了解产品及安装方面的更多信息,请登录 H3C 网站 www.h3c.com...