Subscribe to Our Youtube Channel
Related Manuals for H3C PSR2400-54A
Summary of Contents for H3C PSR2400-54A
- Page 1 H3C PSR2400-54A Power Module User Manual New H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW105-20181116...
- Page 2 All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd. Trademarks Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.
-
Page 3: Table Of Contents
Contents Overview ·················································· 1 Front panel ···································································· 2 LEDs ············································································ 2 Technical specifications ··················································· 3 Power module configuration ·············································· 4 Installing and removing the power module ······· 5 Installing the power module ··············································· 5 ... -
Page 4: Overview
Overview The PSR2400-54A AC-input and DC-output power module is hot swappable and provides a maximum output of 2400 W. Table 1 PSR2400-54A power module features Feature Description Protection against input undervoltage, input overvoltage, output overvoltage, output short Protection circuit, output undercurrent, output overcurrent, and overheat. -
Page 5: Front Panel
Front panel Figure 1 Front panel (1) Power input LED (AC OK) (2) Handle (3) AC input receptacle (4) Latch (5) Power output LED (DC OK) (6) Air outlet vents LEDs The PSR2400-54A power module has two LEDs. -
Page 6: Technical Specifications
Table 2 LED description Mark Color Description No AC power input. Power Low AC input voltage. The power input module has entered self-protection mode. Green Normal AC input. Green Normal DC output. A DC output failure has occurred, for example, output short circuit, Power output overcurrent, output output... -
Page 7: Power Module Configuration
Item Specifications Maximum input current 16 A Maximum output current 44.5 A • 1200 W @ 110 VAC Maximum output power • 2400 W @ 220 VAC 41 × 100 × 332 mm (1.61 × 3.94 × Dimensions (H × W × D) 13.07 in) Operating –10°C to +50°C (–14°F to... -
Page 8: Installing And Removing The Power Module
Installing and removing the power module Installing the power module To avoid bodily injury and device damage, follow the procedures Figure 2 to install a power module. Figure 2 Power module installation procedure Before the installation, prepare an ESD wrist strap and a flat-blade screwdriver yourself. - Page 9 Remove the blank panel from the target power module slot. If the blank panel is as shown in Figure 3, thread the flat-blade screwdriver through the hole in the handle of the blank panel and pull the blank panel out. If the blank panel is as shown in Figure 4, put your forefinger...
- Page 10 Figure 4 Removing a blank panel (2) Unpack the power module. Correctly orient the power module. If you install the power module in a left power module slot, make sure the latch is above the handle. If you install the power module in a right power module slot, make sure the latch is below the handle.
-
Page 11: Connecting The Power Cord
The power module uses two product codes PSR2400-54A and PSR2400-54A-XC for sale. The power cord shipped with the power module depends on the product code. For product code PSR2400-54A, the power cord uses a 16A AC power cord with a C19 angled connector, shown in Figure 6. - Page 12 To connect the power cord: Plug the AC power cord connector into the AC input receptacle of the power module. Use a removable cable tie or self-adhesive cable tie to secure the power cord to the handle of the power module. Route the power cords of the left power modules to the left side.
-
Page 13: Removing A Power Module
Figure 7 Securing the power cord with a straight entry C19 connector by using an self-adhesive cable tie Plug the other end of the power cord into an AC power receptacle, and turn on the circuit breaker. Verify that the power input LED is ON. If the LED is on, the power cord is correctly connected. -
Page 14: Removing The Power Cord
Figure 8 Power module removal procedure Before you remove a power module, prepare an ESD wrist strap yourself. Removing the power cord Turn off the circuit breaker of the power cord. Wear an ESD wrist strap, and make sure the strap makes good skin contact and is correctly grounded. - Page 15 To remove the power module: Pressing the latch towards the handle direction, pull the power module out along the guide rails until it is part way out of the slot. As shown in Figure 9, grasping the handle of the power module with one hand and supporting the bottom of the power module with the other hand, pull the module slowly along the guide rails out of the slot.
Need help?
Do you have a question about the PSR2400-54A and is the answer not in the manual?
Questions and answers