Page 1
H3C PSR2400-54D Power Module User Manual New H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW103-20181116...
Page 2
All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd. Trademarks Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.
Contents Overview ·················································· 1 Front panel ···································································· 2 LEDs ············································································ 2 Technical specifications ··················································· 4 Power module configuration ·············································· 4 Installing and removing the power module ······· 6 Installing the power module ··············································· 6 ...
Overview The PSR2400-54D DC-input and DC-output power module is hot swappable and provides a maximum output of 2400 W. Table 1 PSR2400-54D power module features Feature Description Protection against input under-voltage, input over-voltage, output over-voltage, output short Protection circuit, output under-current, output over-current, and overheat.
Front panel Figure 1 Front panel (1) Power input LED (2) Handle (3) Screw hole for fastening the power cord connector (4) Latch (5) DC-input receptacle (6) Power output LED (7) Air vents LEDs The PSR2400-54D power module has two LEDs.
Page 6
Table 2 LED description Mark Color Description No DC power input. Power Low DC input voltage. The input INPUT OK power module has entered protected state. Green Normal DC input. Green Normal DC output. DC output failure. An alarm condition occurs, for example, output short Power circuit, output over-current,...
Technical specifications Table 3 Technical specifications Item Specifications Rated input voltage –48 V to –60 V Rated output voltage 54 V Maximum input current 80 A Maximum output current 44.5 A Maximum output power 2400 W 41 × 100 × 332 mm (1.61 × 3.94 Dimensions (H ×...
Page 8
When one mains power input is provided, you can configure the power modules in N+1 or N+N redundancy. N+1 or N+N must be not greater than the total number of power module slots. • For easy usage and maintenance, configure a circuit breaker for each power input.
Installing and removing the power module Installing the power module To avoid bodily injury and device damage, follow the procedures Figure 2 to install a power module. Figure 2 Power module installation procedure Before the installation, prepare an ESD wrist strap and a flat-blade screwdriver yourself.
Installing the power module Wear an ESD wrist strap, and make sure the strap makes good skin contact and is reliably grounded. Remove the blank panel from the target power module slot. If the blank panel is as shown in Figure 3, thread the flat-blade screwdriver through the hole in the handle of the...
Page 11
Figure 4 Removing a blank panel (2) Unpack the power module. Correctly orient the power module. If you install the power module in a left power module slot, make sure the latch is above the handle. If you install the power module in a right power module slot, make sure the latch is below the handle.
Figure 5 Installing the power module Connecting the power cord WARNING! • Make sure each power cord has a separate circuit breaker. • Before you connect the DC power cord to the DC source terminal block. Make sure the circuit breakers are turned off. To connect the power cord: Insert the power cord connector into the DC input receptacle on the power module.
Removing the power module To avoid device damage and bodily injury, follow the procedures Figure 6 to remove the power module. Figure 6 Power module removal procedure Before you remove the power module, prepare an ESD wrist strap yourself. Removing the power cord Turn off the circuit breaker of the power cord.
Removing the power module CAUTION: • Before you insert a removed power module into a power module slot, make sure the LEDs on the power module are off. • Avoid scalding your hands when you remove the power module. To remove the power module: Pressing the latch towards the handle direction, pull the power module out along the guide rails until it is part way out of the slot.
Page 15
Place the power module on an antistatic mat. Install the blank panel in the power module slot.