Table of Contents
Advertisement
Command
LAN/IP Configuration and Setup (see also Set IP/Subnet/Gateway (all at once)) (continued)
Query DNS server IP address
Query number of IP connections
KEY:
X7^
= IP Address (xxx.xxx.xxx.xxx):
Set IP/Subnet/Gateway (all at once)
Set IP address
Set IP/Subnet addresses
Set IP/Subnet/Gateway addresses
View IP/Subnet/Gateway
addresses
NOTE:
Setting any values with the CISG command changes DHCP from on to off and the Cisg response is followed by Boot2 response to
verbose listeners.
KEY:
X7^
= IP Address (xxx.xxx.xxx.xxx):
X7(
= Prefix (subnet mask bits):
NOTE:
Per industry standards, there cannot be any
E13
results in an
message.
NTP (Network Time Protocol)
Enable NTP to set the time
Disable NTP
Sync NTP now
Query NTP status
Set single NTP IP address
Set multiple NTP IP addresses
Clear all NTP IP addresses
View NTP IP address
KEY:
X@
= Status:
X7^
= IP Address (xxx.xxx.xxx.xxx):
ASCII Command
(Host to Switcher)
E
}
DI
E
}
CC
Leading zeros in each of the 4 fields are optional in setting values and are expressed in
returned values. Factory Default IP address:
Default Gateway IP addre
E
X7^
}
1*
CISG
E
X7^
X7(
}
1*
/
CISG
E
X7^
X7(
X7^
}
1*
/
*
CISG
E
}
1CISG
Leading zeros in each of the 4 fields are optional in setting values and are expressed in
returned values. Factory Default IP address:
Default Gateway IP addre
Subnet 255.255.0.0 is represented as a Prefix value by /16. Default subnet mask bitsresponse for
esc CISG command = /16.
1
bits to the right of a
255.255.128.0
is correct.
E
}
1 NTEN
E
}
0 NTEN
E
}
2 NTEN
E
}
NTEN
E
}
X7^ NTIP
E
}
X7^ *... X7^ NTIP
E
}
• NTIP
E
}
NTIP
0
1
= Off
= On
Leading zeros in each of the 4 fields are optional in setting values and are expressed in
returned values. Factory Default IP address:
Default Gateway IP addre
Response
(Switcher to Host)
X7^]
]
{number of connections}
192.168.254.254;
ss: 0.0.0.0,
Default DNS Server UP address:
X7^
X7(
X7^]
Cisg•1*
/
*
X7^
X7(
X7^]
Cisg•1*
/
*
X7^
X7(
X7^]
Cisg•1*
/
*
X7^
X7(
X7^]
/
*
192.168.254.254;
ss: 0.0.0.0,
Default DNS Server UP address:
0
bit in a subnet mask. Example:
]
Nten1
]
Nten0
]
Nten2
X@]
]
Ntip X7^
]
Ntip X7^ *... X7^
]
Ntip
]
X7^ *... X7^
192.168.254.254;
ss: 0.0.0.0,
Default DNS Server UP address:
DTP2 R 212 Series • SIS Commands
Additional Description
0.0.0.0
IP‑address, prefix, gateway
0.0.0.0
255.255.64.0
is incorrect and
Disables use of NTP service and
uses the local PC to set the time.
Show the NTP service mode (0/1)
Set NTP server IP address
Set multiple NTP server IP
addresses
Sets to default (empty string)
0.0.0.0
49
Advertisement
Table of Contents
