F.F. Group SCMS 210 PLUS Original Instructions Manual page 10

10 | English
ENGLISH
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
The term "power tool" in all of the warnings list-
ed below refers to your mains operated (corded)
power tool or battery operated (cordless) power
tool.
WORKPLACE
1. Keep workplace clean and well lit. Cluttered
and dark workplaces invite accidents.
2. Do not operate power tools in explosive at-
mospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while op-
erating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Nev-
er modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as conduits, radiators, and re-
frigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool.
5. Keep cord away from heat oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock. When oper-
ating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
2. Use safety equipment. Always wear eye pro-
tection. Safety equipment such as dust mask,
non- skid safety shoes, hard hat,or hearing
protection used for appropriate conditions
will reduce person- al injuries.
3. Avoid suddenly starting. Ensure the switch is
in the off position before plugging in. When
your finger on the switch or plugging in pow-
er tools that have the switch on invites acci-
dents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better con-
trol of the power tool in unexpected situa-
tions.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jew-
ellery or long hair can be caught in moving
parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of these devices c an reduce dust related
hazards.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dan-
gerous and must be repaired.
3. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of
starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
7. Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the work-
ing conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazard-
ous situation.
SCMS 210 PLUS