F.F. Group TMS 210 PLUS Original Instructions Manual page 10

10 | English
ENGLISH
GENERAL SAFETY RULES
WARNING
Read all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
The term "power tool" in all of the warnings listed
below refers to your mains operated (corded)
power tool or battery operated (cordless) power
tool.
WORKPLACE
1. Keep workplace clean and well lit. Cluttered
and dark workplaces invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flamma-
ble liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you
to lose control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Nev-
er modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as conduits, radiators, and refrig-
erators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will in-
crease the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
5. Keep cord away from heat oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock. When oper-
ating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operat-
ing power tools may result in serious personal
injury.
2. Use safety equipment. Always wear eye pro-
tection. Safety equipment such as dust mask,
non- skid safety shoes, hard hat,or hearing
protection used for appropriate conditions will
reduce person- al injuries.
3. Avoid suddenly starting. Ensure the switch is in
the off position before plugging in. When your
finger on the switch or plugging in power tools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices c an reduce dust related hazards.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
3. Disconnect the plug from the power source be-
fore making any adjustments, changing acces-
sories, or storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
7. Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the work-
ing conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazard-
ous situation.
SAFETY INSTRUCTIONS FOR MITER SAW
When using this tool should be aware of safety and
must be followed to avoid the risk of equipment
that may cause a fire, short circuit\ and accidents
that occur to users. For the safety of users,
please read the manual carefully before using the
machine.
TMS 210 PLUS