Assembly Instructions
Mode d'assemblage
Sonoma Cubbie Bench
Banc de "cubbie"
Series / séries # SC-4820
If you have any missing parts, please send an email
to parts@prepacmfg.com, visit www.prepacmfg.com
or call: 1-877-PREPAC1 (1-877-773-7221) Mon - Fri
7:00am to 4:30pm Pacific Time (10:00am - 7:30pm
Eastern). Please have your product series number &
date code available.
Si des pièces sont manquantes, veuillez envoyer un
email à parts@prepacmfg.com, visitez
www.prepacmfg.com ou téléphoner au 1-877-
PREPAC1 (1-877-773-7221) lors des heures
suivantes: LUN - VEN 7h 30 à 16h 30, heure du
Pacifique. Veuillez noter le numéro de série avant
de téléphoner. Pour le service en français,
contactez s'il vous plaît votre détaillant.
Tools Needed / Outils nécessaires
Phillips Screwdriver
Tournevis à pointe cruciforme
Flathead Screwdriver
Tournevis principal plat
Hammer / Marteau
1.
Insert cams and connecting rods into the bottom. Insert cams in the unlocked position,
with the opening facing toward the hole for the connecting rod.
Insérez les ferrures et les vis d'assemblage dans le bas. Insérez les ferrures dans la
position déverrouillée, de façon à ce que l'overture soit face au trou de la vis
d'assemblage.
Cam
Ferrure
Sides (2)
Côtés
2a.
Attach one side to bottom and tighten cams using a FLAT
HEAD screwdriver.
Attachez un côté au fond et serrez les cames à l'aide d'un
tournevis PRINCIPAL PLAT.
2b.
Then, attach side to front stabilizer with Confirmat screws.
Puis, attaché le côté au renforcement arrière avec les vis
Confirmat.
Repeat for other side.
Répétition pour l'autre côté.
© 2005-06-09
Parts / Pièces
Top / Dessus (1)
TP-0772 maple / érable
TP-0712 black / noir
Left Side (1)
Côté gauche
SL-0772 maple / érable
SL-0712 black / noir
Hardware / Quincaillerie
15mm Zinc Cam (8)
Ferrure en zinc
RM-0103
24mm Connecting Bolt (4)
Connecting Rod (4)
Vis d'assemblage
Vis d'assemblage 24mm
RM-0583
Cam
Ferrure
Connecting Rod
Titus
Vis d'assemblage
2b
Confirmat screws
& cover caps
Vis Confirmat et
capuchons des vis
Top Molding (1)
Moulure supérieure
TR-0774 maple / érable
TR-0714 black / noir
Gables
Panneau (2)
GA-0773
maple / érable
GA-0713
black / noir
Front Stabilizer (1)
Renforcement
ST-0772 maple / érable
ST-0712 black / noir
Side Molding (2)
Moulure latérale
TR-0773 maple / érable
TR-0713 black / noir
2" Confirmat Screws
Vis Confirmat 2" (8)
RM-0001
¾" Nail (24)
Clou ¾"
RM-0022
RM-0501
Unlocked
Déverrouillé
2a
Tightening Cams
Serrage des ferrures
Use the flat head screwdriver
and turn cams to the RIGHT
almost 180 degrees until tight.
Utilizer le tournevis principal
plat et serrez les ferrures en
tournant vers LA DROITE
jusqu'a 180 degrés.
Right Side (1)
Backer / Dos (1)
Côté droit
BB-9709
SR-0772 maple / érable
maple / érable
SR-0712 black / noir
BB-0114
black / noir
Bottom
Le bas (1)
BT-0772 maple / érable
BT-0712 black / noir
Black Hardware
Quincaillerie noir
HP-0637
Maple Hardware
Quincaillerie érable
Plastic Dowels (12)
HP-0638
Goujons en plastique
RM-0072
Screw Cover Caps (4)
Tack Glide (4)
Capuchons des vis
Patin à clou
RM-0523 maple / érable
RM-0139
RM-0226 black / noir
Bottom
le bas
Shown Upside Down
Montré à l'envers
Titus
Unlocked
Déverrouillé
LB-0534 Page 1 of/de 2
Locked
Verrouillé
Need help?
Do you have a question about the Sonoma SC-4820 and is the answer not in the manual?
Questions and answers