Fieldmann FZP 2030 E User Manual
  1. Manuals
  2. Brands
  3. Fieldmann Manuals
  4. Chainsaw
  5. FZP 2030 E
  6. User manual

Fieldmann FZP 2030 E User Manual

Electric chain saw
Hide thumbs Also See for FZP 2030 E:
Table of Contents

Advertisement

Quick Links

Download this manual
EN
FZP 2030 E

Advertisement

Table of Contents
loading

Related Manuals for Fieldmann FZP 2030 E

Summary of Contents for Fieldmann FZP 2030 E

  • Page 1 FZP 2030 E...

  • Page 2: Table Of Contents

    Table of Contents Electric Chain Saw USER’S MANUAL TABLE OF CONTENTS 1. GENERAL SAFETY REGULATIONS ........................... 4 2. SYMBOLS ................................... 5 3. SAFETY INSTRUCTIONS ..............................7 4. DESCRIPTION OF THE CHAIN SAW ........................9 5. INSTALLING THE GUIDE BAR AND CHAIN .......................10 6.

  • Page 3: General Safety Regulations

    Following the instructions in the included user's manual is a prerequisite for the proper use of the appliance. The user's manual also contains operating, maintenance and repair instructions. The manufacturer assumes no responsibility for accidents or damages arising from failure to comply with these instructions. FZP 2030 E...

  • Page 4: Symbols

    Symbols 2. SYMBOLS Do not expose the power tool to rain. Read the user’s manual carefully before using the tool. In the event that the power cord is damaged, immediately disconnect it from the power supply. When working, always use a safety helmet, safety glasses and ear protection.
  • Page 5 Use protective gloves when working. Use solid insulating work footwear. Use ear protection. Hold the tools with both hands! Disconnect the power cord plug before any maintenance operation from the power outlet. FZP 2030 E...

  • Page 6: Safety Instructions

    Safety Instructions 3. SAFETY INSTRUCTIONS ATTENTION! Acquaint yourself with all warnings and safety instructions and with operation instructions for the power tool. ATTENTION! Not adhering to warnings or safety instructions may result in injury by electrical shock, a fire and/or serious injury.
  • Page 7 Service Have your power tools repaired by a qualified person who will use original spare parts. In this manner, the same level of safety will be ensured as before the repair of the power tool. FZP 2030 E...

  • Page 8: Description Of The Chain Saw

    Safety instructions | Description of the chain saw Storage transport and store power tools only with the protective cover on clean and maintain power tools thoroughly before storing them secure power tools against oil leakage, damage or injury before transporting them 4.

  • Page 9: Installing The Guide Bar And Chain

    (see fig. 5) ATTENTION! The chain is correctly tensioned if it is possible to lift chain off the guide bar and its height in the horizontal position in the middle of the guide bar is 3 to 4 mm. FZP 2030 E...

  • Page 10: Filling The Chain Saw Oil Tank

    Filling the chain saw oil tank | Operating the chain saw 6. FILLING THE CHAIN SAW OIL TANK ATTENTION! A new chain requires a certain running-in period, which is usually 5 minutes. The lubrication of the chain is very important during this phase. After this running-in period, check the chain tension and readjust if necessary.

  • Page 11: Chain Brake

    Check that the chain brake is in order. A correctly functioning chain brake will protect you against potential injury, which could result from kickback. If the brake is not working properly, have it adjusted or repaired at an authorised service centre. FZP 2030 E...

  • Page 12: Adjusting The Chain Tension

    Adjusting the chain tension | Using the chain saw | cutting 9. ADJUSTING THE CHAIN TENSION ATTENTION! Due to the effect of higher temperatures, during operation the saw chain has a tendency to lengthen. Longer chain is released and can slip off the guide bar. ATTENTION! This chain saw has a chain tensioning system that does not require any tools.
  • Page 13 Only operate the chain saw when the engine is switched off and the bar is protected by the protective cover. FZP 2030 E...

  • Page 14: Cleaning And Maintenance

    Cutting | Cleaning and maintenance Log lying on the ground Cut the log in half, then turn it over and finish it from the opposite side. Log above the ground In part “A” make a cut from below to a third of the log and then complete the cut from above.

  • Page 15: Sharpening The Saw Chain

    Place the file guide at the desired angle (mark A, see figure). Check that the mark is at 30° on the file guide aligned with the centre of the guide bar. This will ensure that you will file at an angle of 30°. FZP 2030 E...

  • Page 16: Replacing The Saw Chain

    Sharpening the saw chain | Replacing the saw chain File the tooth from the inside out (in direction B, see picture) until it is sharp. File only in this direction. Note: Two to three passes of the file should be sufficient to sharpen the tooth. Filing the depth gauge As a result of sharpening the teeth on the chain, the depth gauge tolerance is reduced.

  • Page 17: Storage

    Wipe the chain saw body with a cloth. When cleaning, use a soft cloth dipped in a soap solution. Store the chain saw • in higher shelves or in locked areas out of children's reach • in a dry location FZP 2030 E...

  • Page 18: Technical Specifications

    Technical specifications | Disposal 16. TECHNICAL SPECIFICATIONS Input power 2400W Voltage/frequency 230V–240V/50 Hz Chain pitch 3/8" Guiding groove width 1.3mm Number of chain links 56 links Guide bar length 40cm File diameter Cutting speed 13m/s Oil tank capacity 300ml Weight (with guide bar and chain) 5.3kg Level of acoustic power LWA 107dB (A)

  • Page 19: Declaration Of Conformity

    Declaration of Conformity 18. CONFORMITY DECLARATION EU DECLARATION OF CONFORMITY Product / brand: Electric Chain Saw / FIELDMANN Type / model: FZP 2030-E as factory model HY6110K160 AC 230-240 V, 50 Hz, 2400 W, cutting lenght 406 mm, Class II...
  • Page 21 Záruční podmínky Záručné podmienky Conditions of guarantee Prodávající poskytuje kupují c ímu na výrobek zá­ Predávajúci poskytuje kupujúcemu na výrobok This product is warranted for the period of 24 mon­ ruku trvání 24 měsíců od převzetí výrobku kupu­ 24 mesiacov záruku od jeho prevzatia kupujúcim. ths from the date of purchase to the end-user.
  • Page 22 Jótállási jegy A termék gyártója: FAST ČR, a.s. (U Sanitasu elállásnak nincs helye. A fogyasztó a választott A 151/2003. (IX.22.) Korm.rendeletben meg- 1621, Říčany u Prahy 251 01, Csehország) határozott tartós fogyasztási cikk meghibáso- jogáról másikra térhet át. Az áttéréssel okozott A FAST Hungary Kft.
  • Page 23 A kereskedő tölti ki Megnevezés:................................Típus:................ Gyártási szám: ……………………………………………. A termék azonosításra alkalmas részeinek meghatározása (ha alkalmazható):…………………………………… Vásárlást igazoló bizonylat száma:………………………………………………………………………………. A vásárlás (üzembe helyezés) időpontja: 20......hó.....nap. Kereskedő bélyegzője: Kereskedő aláírása: ………………………………… Kereskedő címe: ……………………………………………… Javítás esetén alkalmazandó A kereskedő vagy szerviznél történő közvetlen bejelentés esetén a szerviz tölti ki A jótállási igény bejelentésének időpontja: ……………………………………………………………………….

Table of Contents