Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fieldmann FZP 3001-B
Summary of Contents for Fieldmann FZP 3001-B
- Page 1 FZP 3001-B...
-
Page 2: Visual Appendix
English ..............................11 - 29 Čeština ..............................31 - 49 Slovenčina ............................51 - 69 Magyarul ............................71 - 90 Polski ..............................91 - 111 Русский ............................119 - 135 FZP 3001-B... - Page 4 FZP 3001-B...
- Page 6 FZP 3001-B...
- Page 8 FZP 3001-B...
- Page 10 FZP 3001-B...
-
Page 11: Table Of Contents
Contents Chainsaw INTSTRUCTIONS FOR USE Thank you for buying this chainsaw. Before use, please be sure to carefully read these instructions and keep them for possible future reference. CONTENTS VISUAL APPENDIX ........................... 2 GENERAL SAFETY GUIDELINES ....................13 Important safety warnings Package Instructions for use EXPLANATION OF INSTRUCTION LABELS ATTACHED TO THE MACHINE ..... - Page 12 SAWING .............................. 24 Kickback protection Tree felling MAINTENANCE ..........................26 Maintenance after each use Points of regular maintenance CHAIN AND GUIDE MAINTENANCE ..................27 Chain Chain guide SPECIFICATIONS ..........................28 DECLARATION OF CONFORMITY ..................29 DISPOSAL ............................29 FZP 3001-B...
-
Page 13: General Safety Guidelines
General safety instructions 1. . GENERAL SAFETY INSTRUCTIONS Important safety warnings Unpack the product carefully and be sure not to throw away any part of the package before having found all components of the product. Keep the product in a dry place out of reach of children. Read all cautions and instructions. -
Page 14: Explanation Of Instruction Labels Attached To The Machine
Choke icon. Pull the choke out half way to close. Position: rear right of the unit Chain lubrication oil injection icon "MIN" direction - oil injection will decrease; "MAX" direction - oil intake will increase. Position: clutch bottom FZP 3001-B... - Page 15 Explanation of instruction labels attached to the machine H position of the screw (used to set high speed) L position of the screw (used to set low speed) The T position is used to set idle speed. Position: rear left of the unit Please read the instructions for use carefully before using the machine.
-
Page 16: Machine Description And Scope Of Delivery
Refrain from using the machine if you are on drugs that may affect and/or limit your judgment abilities to safely operate the machine. Refrain from using the machine in indoor space as the released gases contain hazardous carbon monoxide. FZP 3001-B... -
Page 17: Working Equipment And Clothing
Safety instructions Never use the machine under any of the following conditions: - The work area is slippery or weather conditions do not allow you to keep stable position when operating the machine. - Under dark, strong fog or poor weather conditions that affect the work area visibility. - In rain, storm or strong wind or other conditions that may be pose danger to using the machine. -
Page 18: Operation
When cutting sprung branches, remember they may be flung forward once their tension is released by cutting the wood fibers. Please check and remove any dry branches that might be released from the falling tree. Please make sure the machine is shut down before you put it away. FZP 3001-B... -
Page 19: Maintenance
Operation | Maintenance A kickback notice for the chainsaw user CAUTION! A kickback may occur if the front of the bar comes into contact with the subject or if the chain is clamped by material being cut in the section. Upon contacting the subject, the saw may be flung backward with the bar moving up and back towards the operator. -
Page 20: Guide And Chain Installation
Tensioning device screw (4) (fig. 6). Note: A newly installed chain will slightly extend after some time of use. Please check the chain tensioning frequently as a loose chain may easily come out of the guide groove or cause its fast wear. FZP 3001-B... -
Page 21: Fuel And Chain Lubrication Oil
Fuel and chain lubrication oil | Motor operation 8. FUEL AND CHAIN LUBRICATION OIL Fuel (fig. 7) Mix common petrol (lead or lead-free, alcohol-free) with quality oil used in air-cooled two stroke engines (manufacturer recommended oils). Recommended fuel mixing ratios: When using Petrol: Oil up to 20 hours... -
Page 22: Lubrication Check
Stop the engine and turn the H and L screws until they both stop. Do not apply excessive force! Then, turn the screws back within the range below: „H“ screw: 13/8 „L“ screw: 11/4 Start the engine and allow it to worm up by pulling out the throttle lever (i.e. at low speed). FZP 3001-B... -
Page 23: Carburettor Anti-Freeze Device
Motor operation Turn the L screw slowly clockwise up to the point where the idle speed reaches its maximum. Then, turn the screw head back counterclockwise by a quarter of turn (¼) . Turn the idle speed adjustment screw (T) counterclockwise until the chain stops. If the idle speed is too low, turn the screw clockwise. -
Page 24: Engine Shutdown
This saw incorporates a chain brake which immediately stops the chain should a kickback occur if it works correctly. The chain brake function should be checked before each saw use. Run the saw at full throttle for 1 - 2 seconds and then lower the front guard. The chain must FZP 3001-B... -
Page 25: Tree Felling
Cutting stop immediately even at full engine speed. If the chain stops slowly or doesn‘t stop at all, please replace the brake jaws and the clutch drum before further use. It is extremely important that the chain brake function and chain sharpening status should be checked before each use in order to keep necessary safety level of the saw in case of a kickback. -
Page 26: Maintenance
Dust deposits on the cylinder ribwork causes the engine to overheat. Regularly check and clean the cylinder ribwork. The air filter and the cylinder head cover must be removed before this action. When reassembling the cover, the wiring with bushings must be positioned correctly. (fig. 31) FZP 3001-B... -
Page 27: Chain And Guide Maintenance
Maintenance | Chain and guide maintenance Note: Make sure that the air inlet holes are clean. Spark plug (fig. 32): If necessary, clean the electrodes with a wire brush and adjust the gap between them to 0,65 mm. Geared pinion (fig. 33): Check the pinion for flaws and excessive wear caused by the chain. -
Page 28: Specifications
Maximum chain length: ............................38cm Gear wheel: ..............................7Tx0.325 Chainsaw pitch: ............................0.325 (in) Chainsaw inclination: ............................0.058 Bar type: ..............................Toothed chain Bar dimensions: ..............................1 8 (in) Oil injection system: ................... Automatic pump with adjuster Instructions Manual - language version only. FZP 3001-B... -
Page 29: Declaration Of Conformity
FAST ČR, a.s., Černokostelecká 1621, 251 01 Říčany u Prahy, tel.: 323204111, declares obligatorily that Fieldmann FZP 3001-B (year of manufacture is marked on the type plate and is followed by the machine serial number) conforms to regulations of the COUNCIL DIRECTIVES: EC no.
Need help?
Do you have a question about the FZP 3001-B and is the answer not in the manual?
Questions and answers