Advertisement
Quick Links
TOYOTA
Preparation
Part Number: PT949-08210 (Dash Cam)
PT949-48210 (Y-Harness)
Kit Contents
Item #
Quantity Reqd.
1
1
4
1
5
2
6
4
7
1
1
1
Hardware Bag Contents
Item #
Quantity Reqd.
1
2
3
Additional Items Required For Installation
Item #
Quantity Reqd.
1
2
Conflicts
None
Recommended Tools
Personal & Vehicle
Protection
Seat protection
Dash protection
Special Tools
Installation Tools
Panel Tool
Socket Wrench
Torque Wrench
Special Chemicals
VDC approved cleaner
General Applicability
Applicable to XLE, Limited models
Recommended Sequence of Application
Item #
Accessory
1
Dashcam (PT949-08210)
2
Y-Harness (PT949-48210)
3
Issue: D 4/14/2021
VENZA
Description
Dashcam Main Unit
Window Mounting Plate
Foam Tape
Cable Ties
Quick Start Guide
Y-Harness
Description
Description
Notes
Notes
Notes
With 10mm socket
With 10mm socket
Notes
To clean windshield
*Mandatory
Page 1 of 11 pages
2021 - DASHCAM (Digital Video Recorder)
Vehicle Service Parts
Item #
Quantity Reqd.
1
2
3
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that torque is
related to safety.
(may be required for reassembly)
Description
DIO
Advertisement
Related Manuals for Toyota VENZA PT949-08210
Summary of Contents for Toyota VENZA PT949-08210
- Page 1 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Preparation Part Number: PT949-08210 (Dash Cam) PT949-48210 (Y-Harness) Kit Contents Vehicle Service Parts (may be required for reassembly) Item # Quantity Reqd. Description Item # Quantity Reqd. Description Dashcam Main Unit Window Mounting Plate...
- Page 2 Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Protect Vehicle and Disconnect Battery (a) Protect the bumper before starting. (b) The engine components and coolant may be hot.
- Page 3 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure 2. Apply Vehicle Protection. (a) Apply vehicle protection to front seats, dash and center console (Fig. 2-1). 3. Install the Windshield Base Plate STOP: The front windshield must be at least 50°F (10°C).
- Page 4 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure (b) Once fully detached, disconnect roof console (Fig. 4-2). Fig. 4-2 5. Remove the TSS Cover (a) Rotate the mirror down to gain adequate clearance (Fig. 5-1). Fig. 5-1 (b) Remove the 2-piece mirror cover plate (Fig.
- Page 5 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure (3) Slide the cover up and back to disengage the lower hooks (Fig. 5-3 circled in yellow). Fig. 5-3 (c) Remove the TSS cover by sliding the cover down (Fig. 5-4) from the TSS cover base.
- Page 6 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure (2) Insert the black Y-Harness male connector into the female vehicle connector. (Fig. 6-2 and 6-3) NOTE: For XLE models, there is only 1 connecter (Fig 6-2). For Limited models, there are 2 connectors (Fig 6-3). Connect to the black female vehicle connector that is circled in dotted yellow.
- Page 7 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure (a) From the driver side of the windshield, locate the notch in the front edge of the headliner. (b) Route the Dash Cam pigtail through the notch and into the headliner (Fig. 8-1).
- Page 8 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure 9. Hook harness protector under headliner (a) Use one hand to slightly pull headliner down and use the other hand to extend the harness protector. Hook the protector under the headliner (Fig. 9-1 and Fig. 9-2).
- Page 9 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure (b) Pull all slack through the headliner opening and form a loop (Fig. 10-2). (c) Wrap connector pair with foam tape (Fig. 10-2). (d) Wrap both in-line fuses with foam tape (Fig.
- Page 10 TOYOTA VENZA 2021 - DASHCAM (Digital Video Recorder) Procedure NOTE: Do not block access to the indicated clip hole or else roof console may not attach correctly. (i) Clip off extra wire tie length. 11. Reassemble the console (a) Reconnect roof console connector.
- Page 11 TOYOTA VENZA 2021 - Dashcam (Digital Video Recorder) Checklist - these points MUST be checked to ensure a quality installation. Check: Look For: Accessory Function Checks Removed items have been discarded & Verify parts replaced items are in place Vehicle Startup Confirm Dashcam does not emit continuous Power LEDs light up.