Related Manuals for Toyota PZQ85-33270
Summary of Contents for Toyota PZQ85-33270
- Page 1 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Fitting Time: 30 minutes Dash Camera Fitting Instruction Page 1 of 19 FI Doc No: PZQ85-33270FI - Issue: 2 -07/12/18...
- Page 2 - Ensure all recyclable discarded vehicle accessory components and packaging are recycled following local recycling regulations. - It is always recommended that this accessory is fitted by a qualified Toyota Technician. - Safely store and protect any removed vehicle components.
- Page 3 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Tools and Material Required Plier Phillip head screw 8mm and 10mm Rachet 10mm Torque Wrench Side cutter (pre-set to 8.5Nm) Trim removal tool Page 3 of 19 FI Doc No: PZQ85-33270FI -...
- Page 4 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 1 For Petrol engine vehicle • Disconnect the negative battery terminal • For petrol engine vehicle go straight to Step 3. Step 2 is for hybrid engine vehicle. Always refer to the vehicle’s Workshop Manual when removing vehicle components.
- Page 5 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 3 • Disconnect the negative battery terminal. • Remove the weather strip from left hand side A pillar panel. • Loosen the left hand side A pillar panel •...
- Page 6 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 4 • Remove the indash side cover left hand side Step 5 • Remove glovebox Step 6 • Remove glove box under cover FI Doc No: PZQ85-33270FI - Issue: 2 -07/12/18...
- Page 7 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 7 • Remove front door scuff plate left hand side Step 8 • Remove cowl side trim left hand side Step 9 • Remove the lower console panel. •...
- Page 8 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 10 • Prepare 3 harness tape (40mm x 80mm). • Cover the dash camera wire as shown. Step 11 • Untighten the adjustment screw of the Dash camera •...
- Page 9 Prepare fitting template and adjust the template to the roof headliner edge and Toyota Safety Sense sensor as shown. Use sticky tape to hold the template. Peel out the adhesive tape on the dash camera.
- Page 10 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 15 After the measuring, cut the adjusted length of the cord guide. Step 16 • Insert the Dash camera wire into the cord guide • Install the cord guide to the roof headliner as shown.
- Page 11 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 18 • Cable tie the dash camera wire to the existing vehicle wire. Do not cable tie the vehicle water hose Step 19 Route the dash camera wire through the indash side cover left area.
- Page 12 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 21 Route the dash camera wire next to the junction box. Cable tie the excess wire to the existing vehicle harness loom Step 22 Vehicle Battery and IG signal Location ...
- Page 13 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 23 Remove the 32 pin connector from junction box. Unwrap a portion of the PVC tape from the back of the connector harness to get easy access to the vehicle battery signal and IG signal.
- Page 14 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 25 IG signal installation Prepare red wire Blue Splice connector. Splice red wire of the Blue Splice connector using Black Splice connector red wire Locate the vehicle Battery signal (Grey wire pin no10) ...
- Page 15 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 26 Ground signal installation Route the dash camera ground signal wire to the lower console panel area as shown. Locate the ground terminal location under the centre console panel as shown.
- Page 16 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 27 Connect the Dash Camera inter connector and then apply harness tape. Step 28 Cable tie the ground signal wire as shown. Step 29 Bundle the excess wire to the existing vehicle harness behind the cowl side trim area.
- Page 17 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 30 Dash Camera Initial Setting 1) Insert the Micro SD card into the Dash Camera. 2) Re connect the battery 3) Take the vehicle outside and park in open area to get proper GPS signal.
- Page 18 COROLLA HATCH BACK JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 DASH CAMERA CIRCUIT DIAGRAM FI Doc No: PZQ85-33270FI - Issue: 2 -07/12/18 Page 18 of 19...