Advertisement
Quick Links
PRADO
JUNE 2018 PRODUCTION ONWARDS
Part No: PZQ85-33270
Fitting Time: 45 minutes
Dash Camera
Fitting Instruction
FI Doc No: PZQ85-33270FI -
Issue: 2 - 17/09/18
Page 1 of 23
04
Advertisement
Related Manuals for Toyota PZQ85-33270
Summary of Contents for Toyota PZQ85-33270
- Page 1 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Fitting Time: 45 minutes Dash Camera Fitting Instruction FI Doc No: PZQ85-33270FI - Issue: 2 - 17/09/18 Page 1 of 23...
- Page 2 - Ensure all recyclable discarded vehicle accessory components and packaging are recycled following local recycling regulations. - It is always recommended that this accessory is fitted by a qualified Toyota Technician. - Safely store and protect any removed vehicle components.
- Page 3 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Tools and Material Required Plier Phillip head screw 8mm and 10mm Rachet 10mm Torque Wrench Side cutter (pre-set to 8.5Nm) Trim removal tool Standard business card or driver license or credit card size paper...
- Page 4 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 1 Always refer to the vehicle’s Workshop Manual when removing vehicle components. • Disconnect the negative battery terminal. Step 2 • Remove left hand side instrument cluster panel as shown. Step 3 •...
- Page 5 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 4 • Remove left hand side front console cover. Step 5 • Remove left hand side front door scuff plate as shown. Step 6 • Remove left hand side cowl side trim as shown.
- Page 6 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 7 • Remove left hand side instrument side panel as shown. Step 8 • Remove indash cluster panel as shown. Step 9 • Remove glove box as shown. Step 10 •...
- Page 7 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 11 • Remove left hand side assist grip. • Remove left hand side A-Pillar panel as shown. Step 12 • Remove heat control panel as shown. Step 13 • Remove sat nav unit as shown.
- Page 8 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 14 • Remove instrument lower panel left hand side. Step 15 • Remove instrument lower switch panel right hand side as shown. Step 16 • Remove meter cluster as shown. FI Doc No: PZQ85-33270FI -...
- Page 9 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 17 • Remove combination meter as shown. • Remove all connectors on the combination meter. Step 18 • Untighten the adjustment screw of the Dash camera • Adjust the camera lens position to the 3...
- Page 10 Prepare fitting template A and adjust the template to the roof headliner edge and Toyota Safety Sense sensor as shown. Use sticky tape to hold the template. FI Doc No: PZQ85-33270FI - Issue: 2 -17/09/18...
- Page 11 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 22 Peel out the adhesive tape on the dash camera. Stick the dash camera, by adjusting it to the template next to “arrow” mark as shown. Remove the fitting template when the dash camera attached on the screen.
- Page 12 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 STEP 23 TO STEP 27 IS FOR VEHICLE WITH RAIN SENSOR (for vehicle without rain sensor go straight to step 28) Step 23 • Prepare standard business card or driver license size paper (55mm width and 85 to 90mm length) •...
- Page 13 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 25 • Prepare 2 harness tape (40mm x 80mm) • Cover the dash camera wire next to wire loop as shown. Step 26 Prior to installing, clean inside of the windscreen in the area to be...
- Page 14 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 28 • Route the dash camera wire inside the roof headliner • Prepare the cord guide and measure the length from the larger end to the dash camera • Mark the desire length.
- Page 15 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 30 • Insert the Dash camera wire into the cord guide • Install the cord guide to the roof headliner as shown. Step 31 • Route dash camera wire to left hand side A...
- Page 16 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 33 • Apply harness tape on to the dash camera wire to protect from sharp edges • Pass through the wire to the glove box area Step 34 • Route the wire to the glovebox area •...
- Page 17 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 36 • Locate Battery signal (pin 21, light blue wire) and IG signal ( Pin 22, red wire) on the combination meter connector The connector view is from wire side Step 37 Battery signal installation ...
- Page 18 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 38 IG signal installation Prepare red wire Blue Splice connector. Splice red wire of the Blue Splice connector using Black Splice connector red wire Locate the vehicle Battery signal (Red wire pin no22) ...
- Page 19 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 40 • Route the dash camera harness (power cable side) to glovebox area through the centre console area. • Cable tie the wire on the existing vehicle harness. Step 41 Ground signal installation •...
- Page 20 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 Step 42 • Connect module side and power side interconnection connector. Step 43 Dash Camera Initial Setting 1) Insert the Micro SD card into the Dash Camera. 2) Re connect the battery 3) Take the vehicle outside and park in open area to get proper GPS signal.
- Page 21 PRADO JUNE 2018 PRODUCTION ONWARDS Part No: PZQ85-33270 DASH CAMERA CIRCUIT DIAGRAM FI Doc No: PZQ85-33270FI - Issue: 2 -17/09/18 Page 21 of 23...