Aritech 1X-E4 Series Operation Manual
Hide thumbs
Also See for 1X-E4 Series:
- Installation manual (100 pages) ,
- Quick installation manual (4 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Aritech 1X-E4 Series
Summary of Contents for Aritech 1X-E4 Series
- Page 1 1X-E4 Series Operation Manual P/N 501-415403-2-50 • ISS 13JUN22...
- Page 2 Copyright © 2022 Carrier. All rights reserved. Trademarks and CleanMe and the 1X-E4 Series name and logo are trademarks of patents Carrier. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Audible indicators 6 Summary of status indications 6 Sounder activation during a fire alarm 10 Control panel operation 11 User levels 11 Public user level operation 12 Operator user level operation 15 Maintenance 21 Regulatory information 22 1X-E4 Series Operation Manual... -
Page 4: Important Information
PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED RESELLER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND SECURITY RELATED PRODUCTS. For more information on warranty disclaimers and product safety information, please check https://firesecurityproducts.com/policy/product-warning/ or scan the QR code: 1X-E4 Series Operation Manual... -
Page 5: Advisory Messages
Note: Note messages advise you of the possible loss of time or effort. They describe how to avoid the loss. Notes are also used to point out important information that you should read. 1X-E4 Series Operation Manual... - Page 6 1X-E4 Series Operation Manual...
-
Page 7: Introduction
Introduction This is the operation manual for 1X-E4 Series conventional fire alarm and evacuation control panels. Read these instructions and all related documentation entirely before operating this product. Product range The 1X-E4 Series includes the models shown below. Table 1: 1X-E4 Series models... -
Page 8: Control Panel Overview
19. Earth Fault LED 9. Service Detector LED 20. Supply Fault LED 10. Expansion I/O Fault/Disabled LED 21. Fire Routing Delay button and LED 11. General Disable button and LED 22. Fire Routing Start button and LEDs 1X-E4 Series Operation Manual... -
Page 9: Operator Controls And Indicators
LED indicates that the evacuation area is disabled or is being tested. Supply LED Green Indicates that the system is powered up correctly. General Fault LED Yellow Indicates a fault. The corresponding zone, device, or function fault LED also flashes. 1X-E4 Series Operation Manual... - Page 10 A steady General Disable LED and a steady yellow LED for the corresponding zone, evacuation area, or fire routing, fault warning (for NEN 2575 with EN 54-13 supervision) or expansion I/O indicates a disablement. 1X-E4 Series Operation Manual...
- Page 11 Indicates an earth isolation fault. Supply Fault LED Yellow Indicates a fault with the power supply. A flashing LED indicates a battery or battery fuse fault. A steady LED indicates a mains or mains fuse fault. 1X-E4 Series Operation Manual...
-
Page 12: Audible Indicators
This section includes a summary of the default control panel status indications. Standby (normal status) Standby, or normal status, is indicated as follows: • Supply LED: On steady. • Fire Routing Delay LED: On steady if a fire routing delay was enabled. • Control panel buzzer: Off. 1X-E4 Series Operation Manual... - Page 13 Corresponding zone, evacuation area, function, or device fault LED: Flashing yellow. • Control panel buzzer: Sounding intermittent. Mains power fault and mains fuse fault indication: • General Fault LED: Flashing. • Supply Fault LED: On steady. • Control panel buzzer: Sounding intermittent. 1X-E4 Series Operation Manual...
- Page 14 I/O LED: On steady yellow. • Control panel buzzer: Off. Disabled fault warning (if configured) is indicated as follows: • General Disable LED: On steady. • Fault Warning LED: On steady yellow. • Control panel buzzer: Off. 1X-E4 Series Operation Manual...
- Page 15 Note: When the control panel indicates out of service, your fire alarm and evacuation system is partly inactive and your site is not properly protected. Contact your installation or maintenance contractor immediately to investigate the problem. 1X-E4 Series Operation Manual...
-
Page 16: Sounder Activation During A Fire Alarm
1 or zone 2. Sounders in evacuation area 2 are activated by a fire alarm in zone 3 or zone 4. NEN 2575 with one All sounders are activated simultaneously by a fire alarm in any evacuation area zone 1X-E4 Series Operation Manual... -
Page 17: Control Panel Operation
The control panel is available with an access key option. The key switch is located on the panel cover. With this option, either the key or the password can be used to enter the operator user level. 1X-E4 Series Operation Manual... -
Page 18: Public User Level Operation
Flashing Fire Routing Delay LED during a fire alarm: A configured delay is active. Fire routing is activated when the configured delay elapses or when the delay is cancelled. A fire alarm activated by a manual call point overrides any configured delay and activates fire routing immediately. 1X-E4 Series Operation Manual... - Page 19 1 to 4 and the other panel has a zone range of 4 to 7. Sharing zone 4 will allow activating evacuation area 4 and 1 of one control panel with events of zone 4 in the other panel. 1X-E4 Series Operation Manual...
- Page 20 4 to disappear, indicating that the control panel has zone 4 disabled. At this point, you will know the alarm is from zone 4 of panel 2. You can confirm this by pushing Enter for 3 seconds at panel 2. In this case, the yellow LED indication disappears. 1X-E4 Series Operation Manual...
-
Page 21: Operator User Level Operation
Disable or enable fire routing [1] • Disable or enable other features (all expansion boards and fault warning outputs in NEN 2575 with EN 54-13 supervision mode) [1] These operations can be performed when the control panel is in alarm. 1X-E4 Series Operation Manual... - Page 22 (by pressing the All Sounders Stop button) and remain stopped when the standard fire routing delay time has elapsed. The extended fire routing delay also becomes the active delay when an extended fire routing delay switch is activated while the standard fire routing delay elapses. 1X-E4 Series Operation Manual...
- Page 23 Note: The control panel buzzer and sounders may be configured not to sound when an alarm is activated in a zone being tested. Contact your fire system installation or maintenance contractor to confirm your configuration details. 1X-E4 Series Operation Manual...
- Page 24 To end the test, press the General Test button, and then press the Evacuation Area button again. If there is a fire alarm the fire panel will exit the test and respond to the alarm as configured. 1X-E4 Series Operation Manual...
- Page 25 Fire Routing Start LED: On steady yellow. To enable fire routing, press the General Disable button, and then press the Fire Routing Start button again. Note: Disabled fire routing does not operate or indicate a fault if there is a fire alarm. 1X-E4 Series Operation Manual...
- Page 26 To enable a disabled option, press the General Disable button for more than 3 seconds, press the 1 and 3 buttons to select the option to be enabled, and then press Enter. Note: Disabled expansion boards do not operate or indicate faults. 1X-E4 Series Operation Manual...
-
Page 27: Maintenance
Keep the outside and inside of the control panel clean. Carry out periodic cleaning using a damp cloth for the outside. Do not use products containing solvents to clean the unit. Do not clean the inside of the cabinet with liquid products. 1X-E4 Series Operation Manual... -
Page 28: Regulatory Information
Regulatory information European standards for fire control and indicating equipment The 1X-E4 Series four-zone conventional fire and evacuation control panels have been designed in accordance with European EN 54-2, EN 54-4 and NEN 2575 standards. In addition, the control panel complies with the following EN 54-2 optional... - Page 29 Year of first CE marking Year of first UKCA marking Declaration of Performance 360-3100-1099 number Product identification See model number on product identification label Intended use See the product Declaration of Performance Declared performance See the product Declaration of Performance 1X-E4 Series Operation Manual...