Table of Contents
Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
S.R.
SMITH
INSTALLATION AND USE ON RESIDENTIAL INGROUND SWIMMING
POOLS ONLY. THE CYCLONE IS NEVER TO BE INSTALLED AND USED
ON ABOVEGROUND POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT
DOCKS, FLOATING DOCKS OR PLATFORMS OR OTHER BODIES OF
WATER SUCH AS LAKES, PONDS, RIVERS, ETC.
SRS AUSTRALIA, PTY LTD
12 Enterprise St
Richlands QLD 4077
Australia
Phone 07 3812 2283 • Fax 07 3812 1187
www.srsmith.com/au
06-510
CYCLONE
INSTRUCTIONS
CYCLONE
SLIDES
ARE
MANUFACTURED
S.R. SMITH, LLC
CORPORATE HEADQUARTERS
P.O. Box 400 • 1017 S.W. Berg Parkway
Canby, Oregon 97013
Phone (503) 266 2231 • Fax (503) 266 4334
www.srsmith.com
FOR
USA
OCT19
Advertisement
Table of Contents
Related Manuals for S.R.Smith CYCLONE
Summary of Contents for S.R.Smith CYCLONE
- Page 1 SLIDES MANUFACTURED INSTALLATION AND USE ON RESIDENTIAL INGROUND SWIMMING POOLS ONLY. THE CYCLONE IS NEVER TO BE INSTALLED AND USED ON ABOVEGROUND POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS OR OTHER BODIES OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC.
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ............................3 INSTALLED CYCLONE STRUCTURAL & INSTALLATION CHECKLIST ........... 4 MAINTENANCE INSTRUCTIONS ........................ 4 ASSEMBLED CYCLONE LAYOUT ......................5 PARTS LIST ..............................6 ASSEMBLY INSTRUCTIONS ........................7 Tools Required ............................7 Gasket Installation ............................. 7 Cyclone Assembly ............................. 8 ON-DECK MOUNTING INSTRUCTIONS ..................... -
Page 3: Introduction
DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH CYCLONE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC. -
Page 4: Installed Cyclone Structural & Installation Checklist
Observe the position of the exit of the slide as shown in FIGURE F, FIGURE G, and FIGURE I on pages 11 and 12. MAINTENANCE INSTRUCTIONS When hosing down the deck, hose your Cyclone to wash away any dust, dirt or other debris, which may have accumulated. Be sure that all connections are secure. Tighten hardware if necessary. -
Page 5: Assembled Cyclone Layout
ASSEMBLED CYCLONE LAYOUT FIGURE A... -
Page 6: Parts List
PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. KIT A KIT B KIT A 69-209-113 CYCLONE HARDWARE KIT 1 ea. KIT B 69-209-710 CYCLONE WATER KIT 1 ea. 3/8” HEX NUT ● 5-139 2 ea. 3/8” LOCK WASHER ● 5-151 2 ea. -
Page 7: Assembly Instructions
Properly installed, the gasket will extend from one side of the slide to the other and be centered in the groove, front to back. • Continue to assemble your Cyclone as described on page 8, and ensure the gasket remains in place as you handle the sections. 1. Clean the groove 2. -
Page 8: Cyclone Assembly
Cyclone Assembly FIGURE C Place the upper & lower slide runway sections on the ground. Assemble and fasten as shown in FIGURE C 2.a. 2.b. FIGURE D a. Attach the pedestal to the upper & lower slide sections as shown in FIGURE D in 2 locations. -
Page 9: On-Deck Mounting Instructions
ON-DECK MOUNTING INSTRUCTIONS Place the assembled slide on the deck relative to the pool wall. Ensure that the exit flume clears any coping. Slide may be angled slightly providing all dimensions are maintained as noted in the Manufacturer’s Placement Instructions noted in the following section. With the slide in its proper location, center punch or otherwise mark through the (7) mounting holes at the bottom of the ladder and base so that a visible mark is apparent on the concrete. -
Page 10: Slide Plumbing Instructions
Turn the fitting assembly (9 & 10) until the swivel Outside Runway (10) comes in contact with the wall of the Cyclone Gently tilt the swivel (10) away from the slide and complete one more turn to ensure a good insertion. -
Page 11: Manufacturer's Placement Instructions
OPERATION AND TO REDUCE THE RISK OF SERIOUS INJURY. 1. The critical dimensions for placement of the Cyclone are as shown in FIGURE F and FIGURE G. A. The slide exit runway surface shall not exceed twenty inches (20”) above the water surface as shown in FIGURE F. - Page 12 TABLE 1 Board Minimum Clearance Area “C” Dimension “W” Dimension Pool Type 14’ -6” (4.420 M) 5’ -0” (1.524 M) 14’ -6” (4.420 M) 6’ -0” (1.829 M) 16’ -6” (5.029 M) 6’ -0” (1.829 M) 18’ -6” (5.639 M) 7’...
Need help?
Do you have a question about the CYCLONE and is the answer not in the manual?
Questions and answers