Table of Contents
Advertisement
9683295_oipm_En012_9645931.01-0620 __ 07-02-2020
Palmgren Operating Manual & Parts List
SAFETY RULES (CONTINUED)
TOOL SHOULD BE MAINTAINED
•
Maintain this machine with care. Use a clean sharp cutting blade
for better and safer performance. Follow instructions for
lubricating and changing accessories. Inspect the power supply
cables periodically and if damaged, have them repaired by an
authorized technician.
•
When servicing, use only identical replacement parts. Use of any
other parts will void the warranty. Only use accessories intended
for use with this tool. Approved accessories are available from
your local retailer.
•
The machine must be completely disconnected from its power
source before any maintenance or service is performed. Follow
OSHA lock-out, tag-out procedures to prevent accidental
machine starts.
•
Immediately replace any damaged or obscured warning labels
that are attached to the machine.
•
For your safety, service and maintenance should be performed by
a qualified technician.
•
Band saw blades are sharp. Use suitable gloves when changing
the blade or other adjustments that involve the blade.
•
Use recommended accessories; improper accessories may be
hazardous.
KNOW HOW TO USE TOOL
•
The blade must not move when the saw bow is in a suspended
mode (or raised).
•
Only the blade section used for cutting can be exposed. Use the
blade guides to adjust the blade guards.
•
Never use the machine without its guards in place and working
properly. Keep machine guards in place at all times when the
machine is in use. If removed for maintenance purposes, use
extreme caution and replace the guards immediately.
•
Never put your hands or arms near the cutting area while the
machine is operating.
•
Perform only one operation at a time.
•
Never have several objects in your hands at the same time.
•
Keep your hands as clean as possible.
•
Do not force tool. It will do the job better and more safely at the
rate for which it was intended. Do not use inappropriate
attachments in an attempt to exceed the tool capacity.
•
Use the right tool for the job. Do not attempt to force a small tool
or attachment to do the work of a large industrial tool. There are
certain applications for which this tool was
modify this tool and do not use this tool for a purpose for which
it was not intended.
•
Do not overreach. Keep proper footing and balance at all times.
Do not reach over or across machines while in operation.
•
Remove adjusting keys and wrenches. Check that keys and
adjusting wrenches are removed from the tool or machine work
surface before attaching it to a power supply. Make a habit of
checking to see that keys and adjusting wrenches are removed
before turning on the machine.
.
•
Avoid unintentional starting. Be sure the machine is off when not
in use and before attaching the machine to a power supply.
•
Check for damaged parts. Before using any tool, any part that
appears damaged should be carefully checked to determine that
it will operate properly and perform its intended function. Check
for alignment and binding of moving parts; any broken parts or
mounting pieces should be properly repaired or replaced by a
qualified technician. Do not use the tool if any switch does not
turn on and off properly.
•
Do not over reach. Maintain a balanced stance at all times so that
you do not fall or lean against blades or other moving
•
Never hold the material with the saw in the horizontal position.
Always use the vise and clamp it securely.
•
Read and understand warnings posted on the machine.
•
Always provide adequate support for long and heavy material.
DANGER: Failure to comply with all of these warnings may cause
serious injury.
WARNING: The warnings, cautions and instructions discussed in this
instruction manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product,
but must be supplied by the operator.
MODEL 9683295 10˝ × 16˝
VARIABLE SPEED 3-PHASE BAND SAW
HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2HP
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.2A
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 PH
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1720
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Variable
Blade Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98.5 ~ 347.76
Cut Capacity (W × H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10"× 16"
Round @ 90° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10"
Round @ 45° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10"
Rectangle @ 90° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7" × 16"
Rectangle @ 45° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10" × 12"
Blade Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1" × .035" × 135"
Vise Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0° to 45°
Low Voltage Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
designed. Do not
Dimensions (L × W × D) . . . . . . . . . . . . . . . . . . . . . . . . .77" × 39.5" × 44.5"
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .706 lbs / 794 lbs
3
.
.
SPECIFICATIONS
.
9683295
Advertisement
Table of Contents
