Newco CX-TOUCH Operation Manual
W/qr code specialty drink single cup brewer with auto eject system
Hide thumbs
Also See for CX-TOUCH:
- Operation manual (29 pages) ,
- Programming instructions (2 pages) ,
- Manual (39 pages)
Related Manuals for Newco CX-TOUCH
Summary of Contents for Newco CX-TOUCH
- Page 1 PN 782389_02102012 OPERATION MANUAL NEWCO’S MODEL CX-TOUCH W/QR CODE SPECIALTY DRINK SINGLE CUP BREWER WITH AUTO EJECT SYSTEM 3650 NEW TOWN BLVD. ST. CHARLES MO 63301 WWW.NEWCOCOFFEE.COM 1.800.325.7867...
- Page 2 Table of Contents Machine Labels Page: 3 Introduction & NEWCO Product Warranty Page: 4 Machine Dimensions & Specifications Page: 5 Machine Features Page: 7 Plumbing connections Page: 8 Electrical Hook-Up Page: 8 Installation Instructions Page: 9 Set-Up Instructions Page: 10...
-
Page 3: Warning Labels
Warning Labels NOTICE: Read and follow all notices posted on this machine. Do not damage or destroy these notices as they are for your protection... - Page 4 REFUND. In no event shall Newco be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment,...
-
Page 5: Machine Dimensions & Specifications
Machine Dimensions & Specifications 120 VAC-1700W HEATER-15A USA POWER SUPPLY 1 GALLON TANK 8-12 OZ CUP SIZE TEMPERATURE RANGE 180-205F Machine Functions Product Brewing Door Selection Display Coffee POD Chocolate & Latte Waste Drawer Ingredient Cabinet Water Inlet Drip Tray &... -
Page 6: Front View
Machine Dimensions & Specifications – Continued FRONT VIEW Powder Hoppers RINSE Rinse Button Whipping Chamber Coffee POD Waste Drawer Overflow Drip Tray... -
Page 7: Reset Option
Machine Features • TOUCH SCREEN DISPLAY • FACTORY CALIBRATED-PLUG & PLAY • AUTOMATED POD DRAWER • AUTOMATIC POWDER LEVEL RESET OPTION • POD DRAWER COUNT & COUNT RESET • 88 PRE-PROGRAMMED DRINKS AVAILABLE • WHIPPER RINSE BUTTON • INDEPENDENT POWDER HOPPER COUNTDOWN &... -
Page 8: Plumbing Connections
25 feet from the 1/2” water supply line. A tight coil of copper tubing in the water line will facilitate moving the machine to clean the countertop. Newco does not recommend the use of a saddle valve to install the brewer. -
Page 9: Installation Instructions
Installation Instructions WARNING: - Read and follow installation instructions before plugging or wiring in machine to electrical circuit. Warranty will be void if machine is connected to any voltage other than that specified on the nameplate serial tag. Machine must be on a flat and level surface. Plug or wire in machine to appropriate voltage as noted on the brewer serial tag. - Page 10 Set up instructions for CX TOUCH Machine CX Touch, battery-less units operate differently than older units that contain batteries in the tablet. It is no longer necessary or desirable to use the power switch on the tablet display. The display will power on and off with the brewer automatically. Note that since the tablet does not contain a battery, the tablet will go through a bootup sequence any time the power is cycled to the brewer.
- Page 11 Machine Startup Instructions Fill and install 2lb hoppers with nozzles turned up, Chocolate on left and Milk on right. Make sure “button” on bottom of hopper is seated in slot in sheet metal. Slight manual rotation of the auger gear may be necessary to seat hopper in correct location. Rotate dispense nozzles down into whipper bowl.
- Page 12 Brewing Drinks To dispense a drink, place a cup under the dispense area, press a brew selection and place a pod flat side up (not necessary if the drink selection does not use a pod) Once a selection is made a Submenu for Drink Settings will appear-see page 13 Coffee Drinks Small –Medium- Large Mild-Regular-Bold...
- Page 13 Drinks Submenus Cup Size Coffee Strength Indicator Indicator Cup Strength Selections Cup Size Selections Mild –Regular- Bold Small –Medium- Large Use to Change Use to Change Coffee Strength Cup Size Default Regular Return Button Brew Button Returns to Main Starts Brewing Drink Selection Cycle Menu...
-
Page 14: Programming Instructions
Drink Selection Menu-See Service “ Screens Below Exit Setup Mode Restore Factory Settings Total run cycles-Total drinks Primary Newco Server dispensed Water Filter Remaining Gal* (Future Use) *NOT SHOWN IF NOT USING Pod brew cycles—Tea & Coffee A WATER FILTER... - Page 15 Custom Logo--Wi-Fi Setup SETTING UP A CUSTOM LOGO SCREEN REQUIRES A WI-FI CONNECTION TO THE CX-TOUCH MACHINE. NOTE THAT AFTER THE LOGO IS INSTALLED, THE WI-FI CONNECTION MUST BE TURNED BACK TO “OFF” STATUS. UPDATES THAT MAY OCCUR IF WI-FI IS LEFT ON WILL CAUSE OPERABILITY ISSUES WITH THE BREWER.
- Page 16 COPY IP ADDRESS INFO NAME ENTER CX /data/data/com.newcocoffee.cx FROM CX-TOUCH 3/cache /data/data/com.newcocoffee.cx3/cache 192.168.3.227 6. TAP SERVER CX TO CONNECT TO CX-TOUCH MACHINE 5. ENTER PORT 2121, USERNAME ftp, PASSWORD ftp THEN PRESS Save BAR-SERVER NAME IS NOW SHOWN AS CX...
- Page 17 Install Logo Instructions-Custom Sleep Screen (IOS Apple Version) Cont’d 7. STATUS ON CX-TOUCH MACHINE 8. TO SELECT A FILE TO TRANSFER 9. SELECT THE DIRECTORY WHERE CHANGES TO Connected-Waiting SELECT THE UPLOAD BUTTON THE IMAGE FILE TO BE for transfer TRANSFERRED RESIDES 10.
-
Page 18: Draining The Hot Water Tank
Service Notes & Troubleshooting These error screens will display a service phone number to call if entered in “Setup” Menu (Page 15) *Usually repairing a bad connection or replacing the indicated motor will remedy the problem. Display Reads Possible Cause(s) Remedies Notes Initial fill time longer than 8... - Page 19 Brewing Instructions for CX Touch W/QRC Option Choose Drink Strength and Hold smart phone here to On smart phone, choose & Cup Size. Touch “Next”. download & access menu. touch selection. Point smart phone at QR code scanner. The pod door will open and The brew cycle can be pod holder will extend.
- Page 20 To change from default Touch to highlight the “Combined” box. “Combined” mode to Using the minus sign (-) tap until “ON” After the brew cycle is complete, “Touchless” only mode tap appears. If Touch only is desired, repeat the above screen will appear and the TEA &...
-
Page 21: Machine Access Points
Machine Access Points Top Cover Brew Mech Access Tank Access Main Rear Cover Tank, Pump Access, Sidecar Cover Transformer, Fill Valve Control Board Access... -
Page 22: Pod Brew Mechanism Removal
Pod Brew Mechanism Removal Front View From Drip Tray 1. Remove (2) Outer Brass Nuts Save for Re-Assembly Front View - Cover Off 3. Unsnap Water Fitting: Pull out Water fitting 4. Unsnap Wiring Harness-Lift Brew Mech Up and Out of Machine... - Page 23 Whipper Assembly PN 767377 ITEM # PART NUMBER & DESCRIPTION 767376 WHIPPER STEAM CAP 767195 WHIPPER MOTOR 767196 BASE, WHIPPER MOUNTING 767390,O-RING WHIPPER BASE RED [NOT SHOWN] 767197 WHIPPER IMPELLER 767365 WHIPPER BOWL 767200 WHIPPER NOZZLE 781566 WHIPPER SEAL (REPLACE AFTER 5000 CYCLES)
- Page 24 Tank Assembly PN 780048 ITEM # PART NUMBER DESCRIPTION QTY/EA 110958 RELAY, 12 VDC SPST 30A 111593 HI-LIMIT THERMOSTAT GEAR PUMP ASS’Y 109937 PUMP ASS’Y W/ELBOW (HOT WATER) 781772 780253 TANK ONLY 773056 AIR PUMP, POD 500396 LIQUID LEVEL PROBE& BUSHING 151677 DUAL TEMP THERM PROBE 100149...
-
Page 25: Part Number & Description
Whipper Cannister Assembly (767377) & (767385 & 767386) ITEM # PART NUMBER & DESCRIPTION 780796-HOPPER ASS’Y, RH (LATTE) 767202-ELBOW, 7CM,RH 767376-WHIPPER CAP 767365-BOWL, WHIPPER, 767197-IMPELLER 767196-WHIPPER BASE, 767195- MOTOR 767200-NOZZLE, WHIPPER 781040-BULKHEAD, WATER (NOT SHOWN) 767201-ELBOW, 7CM,LH 780197-HOPPER ASS’Y, LH (CHOCOLATE) 780153 -HOPPER LID-BROWN 780154-HOPPER LID-WHITE... - Page 26 Your CX-3 can be equipped with various optional brew mechanisms to provide brewing choices tailored to your specific needs. For information on these optional brew mechanisms and associated replacement parts contact NEWCO Technical Services at 1-800-556-3926 or NEWCO Customer Service at 1-800-325-7867.
-
Page 27: Wiring Diagram
Wiring Diagram 782305 CONTROL BOARD ONLY 782306 C O N T R O L BOARD AND BRACKET ASS'Y... - Page 28 Left Blank Intentionally...