Summary of Contents for Newco Bistro Touch BISTRO-TCH
Page 1
PN. 128142 10-17-18 Bistro Touch Date Revised 02/24/22 DB Operating Instruction Manual Model BISTRO-TCH Including Touchless QR Code Capability 1-800-325-7867 3650 NEW TOWN BLVD ST. CHARLES MO 63301 WWW.NEWCOCOFFEE.COM...
Table of Contents & Newco Product Warranty ....4 Introduction Machine Dimensions & Specifications ....5 Machine Features ............6 Plumbing Connections ..........7 Plumber’s Installation Instructions ......7 Electrical Hook-Up ............7 Installation Instructions ..........8 Set up instructions ............. 9 Product Installation Procedure ........
Page 3
Warning Labels NOTICE: Read and follow all notices posted on this machine. Do not damage or destroy these notices as they are for your protection WARNING DO NOT OVERLOAD CIRCUIT. ALWAYS ELECTRICALLY GROUND THE CHASSIS OR ADAPTOR PLUG. ...
This warranty is conditioned on the Buyer 1) giving Newco prompt notice of any claim to be made under this warranty by telephone at (800) 556-3926 or by writing to 3650 New Town Blvd, Saint Charles, MO 63301;...
Machine Dimensions & Specifications 120 VAC-1600W HEATER-15A USA POWER SUPPLY 120 VAC-1400W HEATER-15A CANADIAN POWER SUPPLY 1/2 GALLON TANK 6-20 OZ CUP SIZE TEMPERATURE RANGE 140-205F DRIP TRAY PRODUCT & SELECTION DRIP TRAY SWITCH GRATE & DISPLAY WATER INLET & QR READER POWER SWITCH...
Plumbing Connections Plumber’s Installation Instructions CAUTION: Disconnect Power to machine before proceeding with plumbing installation. Attach water line to water filter, rear of machine. Flush water line before installing machine. Machine should be connected to COLD WATER LINE ONLY. Water pressure should be at least 40 lbs. For less than a 25 ft run, use 1/4" copper tubing and connect to 1/2"...
Installation Instructions WARNING: - Read and follow installation instructions before plugging or wiring in machine to electrical circuit. Warranty will be void if machine is connected to any voltage other than that specified on the nameplate serial tag. Machine must be on a flat and level surface. Plug or wire in machine to appropriate voltage as noted on the brewer serial tag.
Open product box and remove the BIB product Fig. 1. Place in Coffee BIB Tray, Fig. 2, (Newco PN 121929) as shown in Fig. 3 Remove the plastic insert from the BIB fitment as shown in Fig. 4 ...
Machine Startup Instructions Fill and install 4lb hoppers with nozzles turned up, Chocolate on left and Milk on right. Make sure “button” on bottom of hopper is seated in slot in sheet metal. Slight manual rotation of the auger gear may be necessary to seat hopper in correct location. Rotate dispense nozzles down into whipper bowl.
Brewing Drinks To dispense a drink, place a cup under the dispense area, press a brew selection To dispense a drink, place a cup under the dispense area, press a brew selection To dispense a drink, place a cup under the dispense area, press a brew selection To dispense a drink, place a cup under the dispense area, press a brew selection , choose a cup size and press “Brew”...
Drink Submenu Decaf Coffee (Or Custom (Or Custom Drink Drink Name) Name) Indicator Coffee Strength Cup Size Indicator Indicator Cup Size Selections Cup Strength Small –Medium- Selections Large Use to Change Mild –Regular- Bold Cup Size Use to Change Default 8-10-12 Coffee Strength Default Regular Brew...
Water filter Reset Total Water Usage OFF, Dispense Only, Always On Default is Dispense Only Select this after changing Total Gallons of water Primary Newco Server filters to reset water filter dispensed* (Future Use) Global Ratio (Reg & Decaf) countdown*...
Page 14
Programming-Cont’d. Drink Selection Menu (custom) Café Blend Coffee Colombian Dark Roast Decaf Espresso Roast French Roast Italian Roast Light Roast Medium Roast Pumpkin Shakin Jamaican Sumatra Drink Selection Menu Ability to turn Drink Selections and/or Cup Sizes On or Off Roast 1 default as coffee Cup Size Choices are 6-8-10-12-16-20 Ounces or OFF Roast 2 default as decaf.
Page 15
Programming-Cont’d SECONDARY PROGRAMMING MODE (SERVICE MENU) RECIPES AND CALIBRATION TAP 3 TIMES ON CENTER OF TOP THEN TAP 3 TIMES ON CENTER OF BOTTOM BAR TO ENTER SECONDARY PROGRAMMING MODE IF A BREWING ICON IS ACCIDENTLY TOUCHED USE THE RETURN ARROW TO TRY AGAIN CALIBRATION RECIPE ENTRY-SEE...
Page 16
Programming-Cont’d NOTE Factory Reset Will NOT Change Recipes SCROLL THROUGH to Default Values RECIPES BY SELECTING RECIPE Note: Changing the NUMBER AS SHOWN values in these THEN USE PLUS recipes can result AND MINUS (+ -) in changes in cup BUTTONS TO volume and taste SCROLL UP AND...
Custom Logo-Wi-Fi Setup SELECT NETWORK TAP CENTER OF LOWER BAR TO SELECT LOCAL SETTINGS ACCESS PROGRAMMING SETUP TO ENTER TABLET SETTINGS SCREEN 1. PRESS “Wi-Fi” ICON TO 2. TURN “WI-FI” ON ACCESS WIFI SETUP & CONNECT TO LOCAL WIFI 4. ENTER PASSWORD 5.
Install Custom Logo (Sleep Screen) (ANDROID VERSION) THIS ADDRESS IS UNIQUE FOR EVERY MACHINE. NOTE THAT IT IS USED FOR THE HOST ADDRESS WHEN SETTING UP COMMUNICATION SITE Install Logo Instructions-Custom Sleep Screen (Android Version) INSTALL AN FTP FILE TRANSFER 1.
Page 19
Install Logo Instructions-Custom Sleep Screen (APPLE IOS VERSION) OPEN THE APP AND SLELCT FTP/FTPS/ SFTH, ADD SERVER, INSTALL THE “ITRANSFER” APP ONTO A LOCAL PHONE OR TABLET. CONNECT THE LOCAL PHONE OR TABLET TO THE SAME WIFI NETWORK AS THE BISTRO-TOUCH. APPLICATION EXAMPLE SHOWN IS “ITRANSFER”...
Page 20
Install Logo Instructions-Custom Sleep Screen Cont’d 7. STATUS ON BISTRO- 8. TO SELECT A FILE TO 9. SELECT THE TOUCH MACHINE CHANGES TRANSFER SELECT THE DIRECTORY WHERE THE TO Connected-Waiting for UPLOAD BUTTON IMAGE FILE TO BE transfer TRANSFERRED RESIDES 12.
Programming --QR Codes FOR “TOUCHLESS” ONLY FOR “TOUCH AND COMBINED” OPERATION: OPERATIONS: TAP 3 TIMES IN TOP LEFT TAP 3 TIMES ON CENTER OF TOP CORNER. THEN TAP 3 TIMES ON BOTTOM THEN TAP 3 TIMES ON CENTER OF RIGHT CORNER. BOTTOM BAR TO ENTER LOWER-LEVEL TO ENTER SECONDARY...
Page 22
Programming QR Codes Cont’d QR Screen for “Touchless Combined”. Use smartphone to get code for recipes. Follow instructions on menu. QR Screen for “Touchless On”. Follow the instructions in above menu. The instructions will take you to the next page’s menus and further instructions. Screen for “Touchless Off”.
Page 23
Programming QR Codes Cont’d NOTE-FRENCH AND ENGLISH LANGUAGES CAN BE TOGGLED FROM THIS SELECTION After choosing the recipe, the cup size, strength of the drink and in this case regular or decaf coffee from the above settings can be made. If the chosen recipe is incorrect, press the return arrow in the top left corner to return to the previous The following menus &...
Page 24
Programming QR Codes Cont’d Hold the QR Code up to the scanner on the door. Recipe will begin to brew automatically and shut off once the scanner recognizes the Code. If for any reason the brewing process needs to be stopped press the CANCEL button to get to “Cancel”...
Daily Cleaning Instructions 1. Push and hold “Rinse” Button until water runs clear (Rinses Mixing bowl and Coffee Mix Chamber) Empty and remove cup 2. Rotate Tab on Whipper Base Counterclockwise to “Five O- Clock” 3. Pull and rotate Dispense Nozzle away from Whipper Bowl 4.
Cleaning & Sanitizing Instructions 1. Remove product from storage area and disconnect BIB connectors as shown in Fig’s 1 & 2 Fig. 2 Fig. 1 Place an empty container in the dispense area of the machine as shown in Fig. 3 Connect the cleaning solution to the BIB connector for Pump and connect cleaning BIB (PN 900083) as shown in Fig 4...
Page 28
Cleaning Instructions 1. Remove the product BIBs from the machine and connect a BIB of cleaning solution to the PUMP 1 (COFFEE) BIB connector as shown in figs. 1-4 page 27. 2. Enter Cleaning and Priming Menu (Page 14) 3. Press the Clean Pumps button on the display panel to enter Cleaning Mode.
Page 29
They keep the check valve open during flushing. Adapters are available for purchase from Newco Enterprises, Inc. (1-800-325- 7867) Newco also supplies BIB cleaning solutions that fit both Scholle and QCD connectors. P/N 320282 QCD FLUSH ADAPTER P/N 120508 SCHOLLE FLUSH ADAPTER...
Page 30
Service Notes & Troubleshooting These error screens will display a service phone number to call if entered in “Setup” Menu (Page 13) For QR errors see pg. 31 *Usually repairing a bad connection or replacing the indicated motor will remedy the problem.
Page 31
Service Notes & Troubleshooting The following Error Codes may appear if the codes are not entered correctly or there is an issue with the scanner unable to read the code. If there are issues, please call Newco Tech Services (1-800-556-3926) for help.