Advertisement
Quick Links
Advertisement
Related Manuals for peerless-AV DS-LEDFLAAF-3X3
Summary of Contents for peerless-AV DS-LEDFLAAF-3X3
- Page 1 DS-LEDFLAAF-3X3 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 2 WARNING ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
-
Page 3: Parts List
Parts (Before beginning, make sure you have all parts shown below). Parts List A ( 19 ) Description Part # connector plate connector plate 096-1714 horizontal spacer 096-1718 vertical spacer 096-1715 side trim 096-1716 harness holder 096-1731 upper left wall plate assembly 096-1719 upper right wall plate assembly 096-1720... - Page 4 B ( 2 ) C ( 3 ) D ( 2 ) J ( 2 ) K ( 2 ) horizontal spacer vertical spacer side trim vertical column vertical column double single 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 5 LED Trim .21" (not included) (5mm) Dimensions are for reference only. Use spacers provided. 3.04" (77mm) 114.61" (2911mm) 103.67" (2633mm) 34.11" 33.80" 58.44" 60.00" (866mm) (858mm) (1484mm) (1524mm) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 6 Use extrusion connectors to connect top horizontal wall plate assemblies. L (8) A (4) Use extrusion connectors to connect bottom wall plate assemblies. A (3) L (6) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 7 WARNING ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood may be covered by gypsum board (drywall) up to 5/8"...
- Page 8 Level wall plates and mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 9 2.5" (64mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (2.5" (64mm) minimum depth required). Level wall plates. Install using wood screws provided. Maximum 80 in. • lb (9 N.M.). N (6) 3/8" (10mm) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 10 Edges must be flush. Secure vertical spacers to the wall flush with the horizontal extrusion. 3/8" (10mm) C (2) N (4) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 11 Use third vertical spacer to align bottom horizontal extrusion flush with vertical spacer, then mark mounting holes on plywood (must be minimum Grade BC, 1/2" (13mm) thick.) Edges must be flush. 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 12 1.75" (44mm) 5/32" 5/32" (4mm) (4mm) Drill mounting holes into supporting surface (1.75" (44mm) minimum depth required). Level wallplates. Install using wood screws provided. Maximum 80 in. • lb (9 N.M.). N (6) 3/8" (10mm) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 13 Remove vertical spacers (C). 3/8" (10mm) C (3) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 14 Insert nuts for vertical assemblies using end of allen wrench. A (2) A (2) A (2) A (2) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 15 Attach vertical assemblies. Do not tighten hardware. L (12) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 16 Space vertical assemblies then tighten hardware. B (2) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 17 Insert vertical assemblies onto extrusions. Do not tighten hardware. L (6) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 18 Space vertical assemblies then tighten hardware. B (2) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 19 Insert vertical assemblies onto extrusions. Do not tighten hardware. L (6) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 20 Space vertical assemblies then tighten hardware. B (2) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 21 Tie a string around the butterfly cut on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 22 Tie a string around the butterfly cut on outer columns in order to level the depth of each vertical column. Loosen, adjust, tighten. 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 23 Tighten or loosen to adjust height. With the string still attached, level the height of each column. Align string with slot in adaptor rail as shown. 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 24 Check adaptor spacing after making adjustments. 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 25 E (4) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 26 M (4) D (2) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 27 Assemble display cabinets, display modules and trim per display manufacturer. O (36) 2019-11-15 #:146-9040-4 (2020-02-18)
- Page 28 Garantia TÜR Garanti̇ Garanzia Záruka www.peerless-av.com/warranty Peerless-AV Peerless-AV Europe Peerless-AV América Latina 2300 White Oak Circle Unit 3 Watford Interchange, Av. de las Industrias 413 Aurora, IL 60502 Colonial Way, Watford, Herts, Parque Industrial Escobedo Email: tech@peerlessmounts.com WD24 4WP, United Kingdom General Escobedo N.L., México 66062...