Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ovlac MINI-BF
Summary of Contents for Ovlac MINI-BF
- Page 1 MINI-BF/HF REV 2021 INSTRUCTIONS MANUAL AND SPARE PARTS...
- Page 2 For the correct use and enjoyment of this equipment, we strongly recommend that the customer read the instructions contained in this manual and use it as a reference for any questions that may arise regarding the operation of your Ovlac equipment. Sincerely yours, Jorge Calvo...
- Page 3 CONSIDERATIONS INDEX This instruction manual describes the operating and maintenance 1.- Security Rules Instructions and spare parts for the indicated equipment. This agricultural equipment, called XPERIENCE, is designed for tilling 2.- Description and technical data the soil, applied to a Tractor with lifting gear and universal threepoint linkage.
-
Page 4: Security Rules
1.- Security Rules 11.- Before starting to work, familiarise yourself with the control devices. Read carefully all the instructions for use of the plough. 12.- Pay the utmost attention to hitching and unhitching the equipment. The manufacturer declines all responsibility for any inconvenience caused by NOT observing the Safety and Accident Prevention Regulations described below. - Page 5 (Fig.1) WARNING To be ready in case of an emergency Before starting to work, read the instructions in the Keep a first aid kit and fire extinguisher on hand. Write manual. down the telephone numbers of doctors, ambulance and fire brigade and keep them near the phone. DANGER Use adequate clothes Do not handle the equipment when it is suspended, danger...
- Page 6 SPECIFIC INSTRUCTIONS FOR WELDING REPAIRS When repair by welding is authorised by the manufacturer, the 4 Our machines are made of high elastic limit (HEL) steels, which following points shall be taken into account generally. means that special attention must be paid to welding processes and filler materials.
-
Page 7: Description And Technical Data
2.- Description and Technical Data HEADSTOCK IDENTIFICATION PLATE* TURNING CYLINDER OSCILLATIN SHAFT WORKIN BODIES SHARE POINT SHARE HYDRAULIC SYSTEM** REAR WHEEL FRAME ANCHOR Note: the number of the plough’s manufacture, engraved on the nameplate, must match the number engraved on the headstock’s support. -
Page 8: Technical Data
Technical Data MODELS MINI F 6 / 6+1 / 6+2 MINI F 8 / 8+1 / 8+2 MINI F 10 / 10+1 / 10+2 Working Width 1,95 / 2,28 / 2,60 2,60 / 2,93 / 3,25 3,25 / 3,58 / 3,90 85 a 140 120 a 180 150 a 220... - Page 9 Important: always works with a pressure in between 100 and 135 bars. NOTE: OVLAC Non-Stop security systems are regulated in factory with an optimum pressure for mid hardness terrains. Fig. 6 Fig.
- Page 10 4.- Turn Up - Adaptation to the tractor - Working bodies OVLAC’s machinery are designed to adapt to the 3 universal points of any Eliminate the painting layer of protection from the bodies tractor. before starting the labor so the earth doesn’t stick to the The oscilating shaft, o barra de enganche, is supplied in two versions bodies.
- Page 11 Check that the distance between A1= A2 (Fig. 7. Pag. 11). At Ovlac’ ploughs the slack is automatically corrected thanks to the oscilating shaft. The third point’s tine must be coupled in order that the end linked over the machine remains slightly higher than the end linked to the tractor.
- Page 12 - Other adjustments For this very same reason, you must check that the tines get a The length of the third option must be adjusted in a way that the perpendicular position to the ground. (Fig. 10). frame adopts a parallel position to the ground, since the opposite The tractor’...
-
Page 13: Working Depth
5.- Working Depth Working depth is regulated through the lifting control of the tractor’ arms. Nevertheless, in order to get an even working depth, all ploughs are equipped with a limiting working depth wheel(Fig. 12) whose height can be regulated through the cylinder T. There is a conection between depth and working width that should be respected for achieving satisfactory results. - Page 14 - Slightly elevate the plough and place the wheel on its transport position. For that you must remove the bolt B, turn the wheel over its holder, and place the bolt on its C position (Fig. 15). Ovlac transport wheels are designed for maximum comfort and easy to use, no operation on the damper neither the depth tops needed.
-
Page 15: Maintenance
7.- Maintenance Must check how tighten the bolts are after the first 2 hours of labor, Watch out for the high pressure leaks specially the ones on the skimmers and shares. Afterwards, check every 100 hours of labor. By finishing the campaign, wash the plough and grease the Leaking fluids from the system might leak strong enough to tear flesh, skimmers to avoid rust. -
Page 16: Optional Equipment
8.- Optional equipment Ovlac ploughs can be equipped with: Skimmers (Fig. 21) Landslide extension (Fig. 22) Transport wheel (Fig. 23) Advanced wheel (Fig. 24) 1st body working width hydraulic adjustment(Fig. 25) Headstock blocking system for transport (Fig. 26) Fig. 21 Fig. -
Page 17: Spare Parts
9.- Spare parts Spare parts orders must always be placed through dealers and will include the next indications: - Type, model and plough's number of manufacturing. This data is indicated on the identification plate of the plough. - Reference of the piece. Indicated on the spareparts catalogue. - Name of the piece and quantity required. - Page 18 Polígono Industrial, C/ TAF, P163 34200 - Venta de Baños Palencia - España +34 979 76 10 11 comercial@ovlac.com www.ovlac.com...
Need help?
Do you have a question about the MINI-BF and is the answer not in the manual?
Questions and answers