Advertisement
Gain Error
Accuracy
(% of FSR )
SINAD
AC
THD
ENOB
Specifications (Cont.)
Analog Output
Channels
2
Resolution
16 bits
Throughput
2 kHz
Operating Mode
Single output
Output Range
0~5, 0~10, ±5, ±10 V
Accuracy
DC
Slew Rate
Dynamic
Performance
Settling Time
Specifications
Specifications
Driving Capability
5 mA
Specifications
Output Impedance
0.1W max.
Non-Isolated Digital Input/Output
Input Channels
8 Non-Isolation TTL
Low
Input Channels
8 Non-Isolation TTL
Input Voltage
Input Channels
8 Non-Isolation TTL
High
Low
Input Voltage
Low
Output Channels
8 Non-Isolation TTL
High
Input Voltage
High
Low
Output Channels
8 Non-Isolation TTL
Output Voltage
Output Channels
8 Non-Isolation TTL
High
Low
Output Voltage
Low
High
Output Voltage
High
Counter
Channels
1
Resolution
32-bit base
Channels
1
Channels
1
Input
Resolution
32-bit base
1 kHz max.
Frequency
Resolution
32-bit base
Input
1 kHz max.
Input
Low
Frequency
1 kHz max.
Clock Input
Frequency
High
Low
Clock Input
Low
Low
High
Gate Input
Clock Input
High
High
Low
Gate Input
Low
High
Gate Input
High
General
I/O Connector Type Removable 10-pin screw terminal x 5
I/O Connector Type Removable 10-pin screw terminal x 5
Dimensions
132 X 80 X 32 mm (5.2" X 3.2" X 1.3")
I/O Connector Type Removable 10-pin screw terminal x 5
Power
Dimensions
132 X 80 X 32 mm (5.2" X 3.2" X 1.3")
360 mA @ +5.0V Typical
Dimensions
132 X 80 X 32 mm (5.2" X 3.2" X 1.3")
Consumption
450 mA @ +5.0 V max.
Power
360 mA @ +5.0V Typical
Power
360 mA @ +5.0V Typical
Consumption
450 mA @ +5.0 V max.
Operation
Consumption
450 mA @ +5.0 V max.
Temperature
Operation
Storage
Temperature
Operation
Temperature
5~ 95 % RH non-condensing
Storage
Relative Humidity
Storage
(refer to IEC 68-2-1, 2)
5~ 95 % RH non-condensing
Relative Humidity
5~ 95 % RH non-condensing
(refer to IEC 68-2-1, 2)
Relative Humidity
(refer to IEC 68-2-1, 2)
Installation
Hardware Installation
After the device driver installation is completed, you can
now go on to install the USB-4716 module in any USB port
that supports the USB 3.0 super speed on your computer.
Please follow the steps below to install the module on your
system:
1. Touch the metal part on the surface of your computer
to neutralize the static electricity that might be in your
body.
2. Plug your USB module into the selected USB port.
Use of excessive force must be avoided; otherwise the
module might get damaged.
2 USB-4716 Startup Manual
0.015 0.03 0.03 0.05 0.1
83 dB
-88 dB
13.5 bit
FIFO Size
N/A
INLE
±2LSB
DNLE
±1LSB
0.125 V/µs
150 µs (to ±1/2
LSB of FSB)
0.0 Vdc (Min) / 1.0Vdc (Max)
2.0 Vdc (Min) / 5.0Vdc (Max)
0.0 Vdc (Min) / 1.0Vdc (Max)
0.0 Vdc (Min) / 1.0Vdc (Max)
2.0 Vdc (Min) / 5.0Vdc (Max)
2.0 Vdc (Min) / 5.0Vdc (Max)
0.4 Vdc / -6mA (Sink)
2.4 Vdc / 6mA (Source)
0.4 Vdc / -6mA (Sink)
0.4 Vdc / -6mA (Sink)
2.4 Vdc / 6mA (Source)
2.4 Vdc / 6mA (Source)
Capability
TTL level
Capability
TTL level
Capability
TTL level
0.0 Vdc (Min) / 1.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
0.0 Vdc (Min) / 1.0 Vdc (Max)
0.0 Vdc (Min) / 1.0 Vdc (Max)
0.0 Vdc (Min) / 1.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
0.0 Vdc (Min) / 1.0 Vdc (Max)
0.0 Vdc (Min) / 1.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
2.0 Vdc (Min) / 5.0 Vdc (Max)
0~60° C (32~140° F)
(refer to IEC 68-2-1, 2)
0~60° C (32~140° F)
0~60° C (32~140° F)
-20~70° C (-4~158° F)
(refer to IEC 68-2-1, 2)
(refer to IEC 68-2-1, 2)
-20~70° C (-4~158° F)
-20~70° C (-4~158° F)
Pin Assignments
Signal Name
Reference Direction Description
AI<0...15>
AGND
AIGND
-
AO0
AGND
AO1
AOGND
-
DI<0..7>
DGND
DO<0..7>
DGND
DGND
-
GATE
DGND
EXT _TRG
DGND
EVT_IN
DGND
P_OUT
DGND
Analog Input Channels 0
Input
through 15.
-
Analog Input Ground.
Analog Output Channels
Output
0/1.
Analog Output Ground.
The analog output volt-
-
ages are referenced to
these nodes.
Input
Digital Input channels.
Output
Digital Output channels.
Digital Ground. This pin
supplies the reference for
-
the digital channels at the
I/O connector.
A/D External Trigger Gate.
When GATE is connected
Input
to +5V, it will disable the
external trigger signal
to input.
A/D External Trigger. This
pin is external trigger
signal input for the A/D
Input
conversion. A low-to-high
edge triggers A/D conver-
sion to start.
Input
External events input ch.
Output
Pulse output channel
Advertisement
