Ip Address Setup With The Printer Front Panel - Kyocera KM-1530 Quick Configuration Manual

The IB-2x must be given the address of the primary WINS server where it will register its host name. It
may optionally be given the address of a secondary WINS server. The DHCP server is often setup to
provide the IB-2x with its host name and the WINS server addresses. Refer to your DHCP server
documentation for the proper setup procedures. Alternatively, the host name and WINS server
addresses may be configured using a web browser or the IB-2x AdminManager utility. See the
Security and Followup Management section later in this guide for information on using these utilities.
WINS registration may be verified by printing the IB-2x Network Status Page. Once the IB-2x has
successfully registered with a WINS server, the WINS Status will show as Registered in the TCP/IP
section.
The following applies to Kyocera Mita printers. See the copier operation manual for information on the
front panel settings for copiers.
1. Press the key. If the first line of the LED panel does not already display INTERFACE, press
∧ ∧ ∧ ∧ ∧ ∨ ∨ ∨ ∨ ∨
the or key until INTERFACE is displayed.
2. If the line below INTERFACE does not already display OPTION, press the
∨ ∨ ∨ ∨ ∨
until OPTION is displayed and press
3. Press the key to enter the Option submenu. (Note: Some older printers may not support front
panel setup. If there is no Option submenu or not all choices are available on the submenu,
please check the firmware requirements listed in the following section.)
∧ ∧ ∧ ∧ ∧ ∨ ∨ ∨ ∨ ∨
4. Press or until TCP/IP is displayed. Press the key to enter the TCP/IP submenu (only
accessible when the TCP/IP protocol is On).
∧ ∧ ∧ ∧ ∧ ∨ ∨ ∨ ∨ ∨
5. Press or until IP Address is displayed. Press the
the last digit of the IP address.
6. Press the or key to move the cursor to the desired digit to change. Press
value of a digit.
7. Once all digits are set as desired, press the
8. Repeat steps 5 - 7 for Subnet Mask and Default Gateway (the router's IP address). If unsure of
the correct Subnet mask and the first number in the IB-2x IP address is from 192 to 254, then use
255.255.255.0 as the Subnet mask.
9. When all settings for IP Address, Subnet Mask, and Default Gateway are completed, press the
key to return to the Option submenu (TCP/IP is displayed).
It is recommended to turn off protocols that are not in use.
∧ ∧ ∧ ∧ ∧
10. Optional: Press
and a ? will appear next to On. Press
the new value. Repeat for each protocol to turn off.
11. Press the key to return to the Interface menu (Option is displayed).
∧ ∧ ∧ ∧ ∧ ∨ ∨ ∨ ∨ ∨
12. Press or until Print Status Page is displayed. Press the
page and verify the new settings.
13. When completed, press the
∨ ∨ ∨ ∨ ∨
or to display the protocol to turn off, e.g. EtherTalk. Press the
∧ ∧ ∧ ∧ ∧
or
key to exit the menu system.
.
key and a cursor will appear under
key to accept the new address.
∨ ∨ ∨ ∨ ∨
to toggle the value to Off and press
14
key, then
∧ ∧ ∧ ∧ ∧ ∨ ∨ ∨ ∨ ∨
or to change the
key
to accept
key twice to print a status
∧ ∧ ∧ ∧ ∧
or