Operating Your Pellet Stove - HAMPTON BAY Greenfire GCi60-2 Owner's Manual

o y
peRating
THE UNIT WILL NOT OPERATE WITH THE DOOR OR ASH BOX OPEN. Open the hopper lid only to re-
fuel or to adjust the controls. the unit will shut down if the hopper lid is left open for longer than two
minutes.
CAUTION: When operating during adverse weather, such as high winds or freezing rain, if the unit exhibits
dramatic changes in combustion stop using the unit immediately. Watch for blocked exhaust outlet.
CAUTION: Radiant surfaces can become very hot and can cause burns when contacted.
PRE-BURN CHECK: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube
and locked in place. Check the hopper for enough pellets to start the unit.
Note: To change fuel type, ensure the Thermostat Switch is set to Manual Mode. Press the Off button and then
press the Fuel Type button to cycle through the available fuel types.
Note: The unit has an automatic cleaning cycle; every thirty minutes the agitator
will turn continuously for one minute to help clean out the burn pot liner.
MANUAL MODE:
All control of circuit board function is adjusted at the circuit board.
INITIAL START-UP: Press the ON / OFF button. The stove will turn on. The
Fuel Type Light will flash (the Auger Feed Rate is pre-programmed during start-up).
The Heat Level Indicator will show the Heat Level that the stove will run at after
start-up. If this is the first time the unit has been started or the unit has run out of
fuel, the auger may need to be primed. The liner can be primed with a handful of
pellets, or after the two minute prefeed, the unit can be restarted.
The agitator will not operate for the first five minutes after the ON button has been pressed.
After the ten minutes it will pulse at the same interval as the feed auger.
When the start-up sequence is complete, the unit will switch to the designated heat setting.
Once a fire has been established, the convection blower will turn on after ten minutes.
To OPERATE: Press the Heat Level buttons to change the desired Heat Level Output setting.
The speed of the convection blower is controlled by the setting of the heat level.
The Feed Trim button pressed in conjunction with the Heat Level adjustment buttons can be used to adjust the feed
trim. It can be increased by two feed settings or it can be decreased by two feed settings.
HIGH/LOW MODE: (Requires a Thermostat or Timer)
INITIAL START-UP: See MANUAL MODE above.
OPERATION: When the thermostat calls for heat (contacts are closed) the stove settings are adjustable as per
Manual Mode. When the thermostat contacts open, the HEAT LEVEL and Fans will
drop down to the LOW setting until the thermostat contacts close again. The stove
will come back to the previous HEAT LEVEL setting once the thermostat contacts
close.
AUTO/OFF MODE: (Requires a Thermostat or Timer)
INITIAL START-UP: See MANUAL MODE above.
OPERATION: When the thermostat contacts close, the unit will light automatically.
Once up to temperature, the stove operates the same as in MANUAL. When the
thermostat contacts open, the stove's HEAT LEVEL and Fans will drop down to the
LOW setting for 30 minutes. If the thermostat contacts close within the 30 minutes,
the HEAT LEVEL will return to the previous MANUAL setting. If the thermostat contacts
remain open, the stove automatically begins its shutdown routine. The stove will re-light
when the thermostat contacts close again.
Hampton GCi60-2 Cast Pellet Insert Owner's Manual
Operating Instructions
p S :
ouR eLLet tove
Premium Grade Pellets
Regular Grade Pellets
Low Grade Pellets
AUTO/OFF
HIGH/
LOW
FUEL TYPE
MANUAL
Figure 3: Thermostat Switch
in MANUAL position.
COMBUSTION
FAN TRIM
5
4
FEED TRIM
3
Starting a Fire
in Your Pellet Stove
HEAT
2
LEVEL
Premium Grade Pellets
Regular Grade Pellets
1
Low Grade Pellets
ON/OFF
AUTO/OFF
HIGH/
LOW
Premium Grade Pellets
FUEL TYPE
Regular Grade Pellets
MANUAL
Low Grade Pellets
Figure 4: Thermostat Switch
in HIGH/LOW position.
Sticker Front
COMBUSTION
FAN TRIM
5
AUTO/OFF
HIGH/
4
LOW
FUEL TYPE
FEED TRIM
MANUAL
3
Figure 5: Thermostat Switch
in AUTO/OFF position.
COMBUSTION
HEAT
FAN TRIM
2
9
5
LEVEL