Advertisement
10.
Unscrew the spring loaded safety valve and, using the funnel, fill the boiler approx. full (upper level
to the sight glass) with hot water if possible. Raise the funnel slightly when pouring in the water so
that the air can escape from the boiler. Use boiled water or rain water if possible (low chalk
11.
Note: The steam whistle can be used to check for any overpressure in the boiler or, before oiling,
12.
Close the steam cut-off valve before oiling the cylinder. The valve is closed when the lever is
below approx. 45 deg pointing backwards (towards sight glass) and open when the lever is below
approx. 45! Pointing forwards (towards smoke stack). Now unscrew the oil filler screw and fill with
WILESCO steam engine oil or car engine oil while turning the flywheel several times so that the oil
is drawn in. Oil frequently so that the piston does not seize. 2-3 drops of oil are sufficient for
approx. 10 minutes operating time. For safety reasons the steam cut-off valve must be closed
when oil is being added. There must not be any steam pressure in the boiler. Lightly oil all the
bearings and linkages. Before refilling the boiler with water, the pressure in the boiler has to be
13.
Place two layers of ESBIT fuel tablets in the burner slide, the lower tablets flat and the
upper tablets on their sides. Then light the tablets. Never use more than 4 fuel tablets at a time.
Use only the original WILESCO burner slide. Caution: Because of the risk of danger from an
open flame, always take the necessary safety precautions. The burner slide is adjustable. The
oxygen supply and the flame height can be adjusted by moving the burner slide in relation to the
air holes (see illustration). Before adding new fuel tablets always check the water level and refill
the boiler with water to ensure that the boiler does not run dry. The ratio of fuel tablets to the
amount of water in the boiler is designed so that the boiler cannot run dry without fuel tablets being
added. The fuel slide must be completely pushed in. Important: After completing the heating
process, remove the burner slide from the guide whilst it is still hot, otherwise unburned fuel
may cause the slide to jam. If the slide becomes jammed, it can be removed by tilting it slightly to
the left or right. Widen the guide slightly using a standard pair of flat pliers.
Note: ESBIT tablets require plenty of oxygen to burn properly. This means if used indoors the
room should be well ventilated. To prevent unpleasant smells, the fuel tablets should be allowed
to burn out they should not be blown out. If there is insufficient water in the boiler, place the burner
slide on a metal plate until the tablets have burned out completely.
14.
Disengage the gears next to the driver cab, by moving the clutch lever sideways. When the water
starts to bubble open the steam valve and turn the flywheel by hand, so that the condensation in
the pipe and cylinder can escape. Engage clutch and put steam engine into operation, by gently
spinning the flywheel. The flywheel can be started-up in either direction, which enables forward
and reverse movement. The speed can be adjusted by means of the steam stop valve.
15.
The exhaust steam which does not escape through the chimney collects as water-oil-condensation
in the container under the chimney, which is why the steam pipe is not soldered, since no pressure
develops in the condensation container (separate from the boiler). After using, remove the
chimney and remove the condensation through the chimney hole, by banging lightly.
16.
The Steam Roller (and Traction engine) can, with the clutch disengaged, be used as a stationary
steam engine. By using the belt drive on the flywheel, the WILESCO range of driving models can
be operated. When the Steam Roller is used as a stationary engine the clutch must always be
17.
After use, remove any water left in the boiler. Be very careful if the water is still hot! Any water
left in the boiler cannot do any damage, but might leave sediment on the sight glass. Any soot
formation on the lower surface of the boiler can be removed with a brush, e.g. an old toothbrush.
Finally, dry the model using a clean cloth. Never remove chalk residues on the sight glass with
18.
Finally, a few comments on the warranty. All WILESCO steam models are carefully checked
before leaving the factory. However, if a problem arises, we will be happy to assist, or carry our
repairs. You can return the steam engine directly to WILESCO or to the distributor. We are sure
you will appreciate fired models cannot be exchanged, but we undertake to repair any fault.
The above information has been given for you to obtain the maximum enjoyment from your steam
engine WILESCO wishes you lots of fun, and Full steam ahead?
Operating instructions:
content).
to check whether the boiler is still under pressure.
released by opening the steam whistle.
disengaged.
vinegar.
Warranty:
Advertisement
