Table of Contents
Advertisement
OPERATING INSTRUCTIONS
Avoid any drafts that alter burner flame patterns. Do
not allow fans to blow directly into the fireplace. Do not
place a blower inside the burn area of the firebox. Ceil-
ing fans may create drafts that alter flame patterns. Soot-
ing and improper burning will result.
During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain
oils, films or bonding agents. These chemicals are not
harmful, but may produce annoying smoke and smells
as they are burned off during the initial operation of the
appliance, possibly causing headaches or eye or lung
irritation. This is a normal and temporary occurrence.
The initial break-in operation should last two to three
hours with the burner at the highest setting. Provide
maximum ventilation by opening windows or doors to
allow odors to dissipate. Any odors remaining after this
initial break-in will be slight and will disappear with con-
tinued use.
This appliance must not be used with glass doors in the
closed position. This can lead to pilot outages and se-
vere sooting outside the fireplace.
FOR YOUR SAFETY READ BEFORE
LIGHTING
Always operate heater with glass doors fully
open.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
A.
This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instruc-
tions exactly.
B.
BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor be-
cause some gases are heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
l
Do not try to light any appliance.
l
Do not touch any electrical switches; do not use
any phones in your building.
l
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
l
If you cannot reach your gas supplier, call the fire
department.
C.
Use only your hand to push in or turn the gas con-
trol knob. Never use tools. If the knob will 8not push
in or turn by hand, don't try to repair It. Call a quali-
fied service technician or gas supplier. Forced or
attempted repair may result in a fire or explosion.
D.
Do not use this appliance if any part has been un-
der water. Immediately call a qualified service tech-
nician to inspect the appliance and to replace any
part of the control system, and any gas control,
which has been under water.
MILLIVOLT CONTROL(MODELS MVA)
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information label.
2. Make sure the manual shutoff valve is fully open.
3. This gas log set is equipped with an ignition de-
vice (piezo) which automatically lights the pilot. If
piezo ignitor does not light the pilot, see instruc-
tions for Match Lighting Instructions, page 18.
4. Turn gas control knob clockwise
position, set the thermostat to the lowest setting
and turn ON/OFF switch to OFF position.
5. Wait (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP!Follow "B" in the safety information label. If
you don't smell gas, go to next step.
6. From OFF position, turn the gas control knob coun
terclockwise
7. With the control knob pushed in, push in and re
lease the piezo ignitor button to light the pilot.
8. Continue pushing the control knob in for a further
60 seconds to prevent the flame detector from
shutting off the gas while the probe is warming up.
Release the control knob.
9. Turn gas control knob counterclockwise
the ON position.
10. After the pilot has been lit for one minute, the burn-
ers can be turned on. Turn the ON/OFF switch to
ON position or adjust thermostat to desired setting.
11.If the gas logs will not operate, follow the instruc
tions To Turn Off Gas To Appliance below and call
your.
WARNING: Wait 30 seconds before readjusting
the heater when the control knob has been turned
down to a lower setting.
15
to the OFF
to IGN position. Push in control.
to
Advertisement
Table of Contents
