Page 1
TY-SB01DL Model No. Operating Instructions DIGITAL LINK Terminal Board English For business use Before connecting, operating or adjusting this product, please read these instructions completely. ● Please keep this manual for future reference. ● Mode d’emploi Plaque à bornes DIGITAL LINK Français...
Safety Precautions Precautions for use (Be sure to observe.) This product is a DIGITAL LINK terminal board used by being attached to a Panasonic display and projector. WARNING Do not touch this product directly by hand. When mounting or removing this product on or from ●...
1 DIGITAL LINK input / LAN terminal O N: T he power is supplied. C onnect a device that sends image and audio signals B link: T he power is supplied to the DIGITAL LINK via the DIGITAL LINK terminal. input / LAN terminal. O r connect to a network to control some of the T he power is not supplied to the DIGITAL LINK Panasonic displays and projectors. For details, refer output terminal. to the Operating Instructions of the display and projector. O FF: T he power is not supplied. 2 DIGITAL LINK output terminal 2, 4 LINK indicator W hen displaying images through multiple daisy chain O N: S ending or receiving DIGITAL LINK signals.
Page 4
Replacing the DIGITAL LINK: Communication method is fixed to DIGITAL LINK. terminal board Long reach: Communication method is fixed to Long reach. Modes allowing communication The replacement instruction below is based on the flat panel display as an example. : Valid For attaching or removing this product to or from the flat ― : Invalid panel display unit, it is recommended to ask a qualified technician or sales dealer. A malfunction may occur due Communication validity to static electricity, etc. Consult the sales dealer. Picture Settings Follow the steps below. transmission Ethernet 232C Note...
Page 5
DIGITAL LINK input / LAN terminal. Analogue signal is output as Digital signal. L AN cable (commercially available) F irst display S econd display T hird display Note ● For daisy chain connection, use a twist pair cable with the same condition as that for the cable used to connect between the transmitter and this unit. P C to control the unit Depending on the cable, a transmission error may E xample: Panasonic ET-YFB200G occur. B lu-ray disc player ● Daisy chain connection is possible up to 10 units, however, the number of connectable units may be P C restricted depending on the cable, signal, device to Note be used, etc. ● Video equipment and connection cables are not ● In daisy chain connection, it may take time for images supplied with this unit. to appear on all the displays.
Page 6
When laying the cable(s), use an instrument such as a cable tester or cable analyser and check whether About installation / connection the cable characteristics are CAT5e or above. When using a relay connector along the path, also include ● Ask a professional or the dealer to carry out the cable this in the measurements. wiring work for DIGITAL LINK connections. Insufficient ● Do not pull cables hard. Also, avoid bending or folding wiring work may cause the inability to apply the cable them forcefully. transmission characteristics and cropped or fuzzy images and sounds. ● The transmission distance between the twisted Others pair cable transmitter and this product is normally ● This product is compatible with Panasonic devices up to 100 meters. When transmitting 4K signal, that support DIGITAL LINK output (ET-YFB100G, the maximum is 50 meters. When the transmitter ET-YFB200G). For the twisted pair cable transmitter supports [Long reach] communication method, the of other manufacturers, see the web site. transmittable distance is up to 150 m. Please note (https://panasonic.net/cns/prodisplays/solutions/ that if exceeding the limit, video or audio may be technology/digital_link/compatible_equipment/) interrupted, or malfunction may be caused during LAN communication. Furthermore, when connecting ● Panasonic has tested other manufacturers’ devices using [Long reach] communication method, according to our check items. This will not guarantee depending on the specification of the transmitters, all the operations. For operation and performance transmittable video signals or the distance may be defects caused by other manufacturers’ devices,...
Specifications Model No. TY-SB01DL DIGITAL LINK input / For RJ45 network connection and DIGITAL LINK connection LAN terminal Long reach mode supported, HDCP2.2 supported DIGITAL LINK IN / DIGITAL LINK output For RJ45 DIGITAL LINK connection terminal Long reach mode supported, HDCP2.2 supported DIGITAL LINK OUT Maximum 150 m (Long reach mode, resolution of 1080/60p (4:4:4 24 bit) or less) transmission 100 m (Resolution of 1080/60p (4:4:4 36 bit) or less) distance 50 m (Resolution of 4K/60p (4:2:0) or less) Supported signal* Motion picture-related signal resolution: 480/60p, 576/50p to 4 096 x 2 160 Still picture-related signal resolution: 640 x 480 to 3 840 x 2 400 (Non-interlace) Dot clock frequency: 25 MHz to 297 MHz * Image signals that can be displayed by displays and projectors depend on the performance of the displays and projectors. Dimensions Width: 195 mm / 7.68” Height: 25 mm / 0.99” Depth: 123.2 mm / 4.85” Mass Approx. 280 / 0.6 lbs net...