Table of Contents
Advertisement
Quick Links
TM
CANplus
CP750-E
Installation Manual
CANplus
Due to continuous product improvement, the information provided in this document is subject to change without notice.
Cattron Support
For remote and communication control systems support, parts and repair, or technical support, visit us online at:
www.cattron.com/contact
Cattron North America Inc., 655 N River Rd NW, Suite A, Warren, OH 44483
TM
Installation Manual
9M01-1000-A501-EN
CP750-E
9M01-1000-A501-EN
Revision A
Advertisement
Table of Contents
Related Manuals for Cattron CANplus CP750-E
Summary of Contents for Cattron CANplus CP750-E
- Page 1 Due to continuous product improvement, the information provided in this document is subject to change without notice. Cattron Support For remote and communication control systems support, parts and repair, or technical support, visit us online at: www.cattron.com/contact Cattron North America Inc., 655 N River Rd NW, Suite A, Warren, OH 44483 9M01-1000-A501-EN Revision A...
- Page 2 Cattron Holdings, Inc., or any of its affiliates or agents shall not be liable for incidental or consequential damages of any kind. All Cattron products are sold pursuant to the Terms and Conditions of Sale, a copy of which will be furnished upon request. When used as a tradename herein, Cattron means Cattron Holdings, Inc.
-
Page 3: Table Of Contents
CANplus CP750-E Installation Manual 1.1.1 I ----------------------------------------------------------------------------------------------------------- 4 NTRODUCTION 2 MECHANICAL MOUNTING --------------------------------------------------------------------------------------------- 5 2.1 A ™ P ------------------------------------------------------------------------------------------------------ 5 ANELS 2.1.1 M ------------------------------------------------------------------------------------------------ 5 OUNTING EMPLATES 3 CONNECTOR PINOUTS ------------------------------------------------------------------------------------------------- 8 3.1 D21 ------------------------------------------------------------------------------------------------- 9 NGINE IN OUT 3.2 A ------------------------------------------------------------------------------------------------ 10 UTOSTART WITCHES... -
Page 4: 1.1.1 Introduction
Engine Distributors and OEMs of engine- driven machines. The engine manufacturer specific application information should be followed for any detailed or specific requirements. Cattron sales and technical support are available at to discuss specialized requirements or custom applications. -
Page 5: Mechanical Mounting
CANplus CP750-E Installation Manual Mechanical Mounting The CP750-E control panel is adaptable to a wide variety of applications. The included engine harness connector facilitates quick installation. The following is a list of installation guidelines: 1) The panel mount shall be a) Easily accessible by the operator. - Page 6 CANplus CP750-E Installation Manual 9M02-1000-A501-EN Revision A...
- Page 7 CANplus CP750-E Installation Manual 9M02-1000-A501-EN Revision A...
-
Page 8: Connector Pinouts
CANplus CP750-E Installation Manual Connector Pinouts Depending on the panel options, the CP750-E has four (4) or six (6) connectors on the back, as described in the following subsections. 9M02-1000-A501-EN Revision A... -
Page 9: D21 To Engine Pin Out
CANplus CP750-E Installation Manual D21 to Engine Pin out This connector contains the typical connections required for electronically or mechanically governed engines. The following is the pinout: Signal Comment Signal Comment 1 A @ Pre-Heat Aux IN 2 Active Low System Voltage Active Low, Temp SW... -
Page 10: Autostart Switches
CANplus CP750-E Installation Manual Autostart Switches Switches Transducers 1 and 2 Tr1 Signal Primary Tr -PWR Tr2 Signal Secondary Tr -PWR AUXIO AUXI/O AUXOUT 1 Alarm buzzer AUXOUT 2 AUX STOP 9M02-1000-A501-EN Revision A... -
Page 11: Modbus
CANplus CP750-E Installation Manual Modbus MODBUS RS485A RS458B 9M02-1000-A501-EN Revision A... -
Page 12: Typical Wiring
Negative voltage surges can damage components. The CP750-E has protection against these negative surges. However, it is still required to have a protection/suppression diode as close to the relay as possible. Cattron recommends the use of relays that have this protection/suppression diode built in. The protection/suppression diode must have sufficient voltage ratings to survive and sufficiently suppress these negative voltage surges. -
Page 13: Testing
CANplus CP750-E Installation Manual Testing WARNING DURING THE FOLLOWING PROCEDURE, CORRECT ANY PROBLEMS BEFORE PROCEEDING TO THE NEXT STEP. CONTINUED TESTING MAY DAMAGE THE PANEL, HARNESS OR ENGINE. Use the following testing procedure: 1) Turning the keyswitch ON initiates self-test; check all connections and battery polarity on failure. -
Page 14: Certifications
CANplus CP750-E Installation Manual Certifications FCC Part 15 Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 15: Industry Canada Certification
CANplus CP750-E Installation Manual Industry Canada Certification Note: These statements are required to be listed in both English and French Languages. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. -
Page 16: Technical Support
CANplus CP750-E Installation Manual Technical Support For remote and communication control systems support, parts and repair, or technical support, visit us online at: www.cattron.com/contact. 9M02-1000-A501-EN Revision A...
Need help?
Do you have a question about the CANplus CP750-E and is the answer not in the manual?
Questions and answers