H2Tu-C-231 List 1E Pairgain Config Screen Options - ADC PAIRGAIN HiGain HDSL2 Manual

152-231-115-03, Revision 03
Table 5. H2TU-C-231 List 1E Standard Config Screen Options (Cont.)
Front-panel
System Settings
Display
Screen Options
Code
H2TU-R TOS TLOS
Loopback
Network NLBP
Loopback Pattern
Table 6. H2TU-C-231 List 1E PairGain Config Screen Options
Front-panel
System Settings
Display
Screen Options
Code
Line Power Feed PWRF
Remote RTPV
Provisioning
Bipolar Violation BPVT
Transparency
(See "Bipolar
Violation
Transparency
(BPVT) Option"
on page 23.)
HDSL2 BER HBER
Threshold
(See "HDSL2 BER
Threshold (HBER)
Option" on
page 23 and
"System Alarm
Output Pins" on
page 61.)
DS1 BER DBER
Threshold
(See "DS1 BER
(DBER) Option"
on page 23.)
Special Loopback SPLB
Mode
SmartJack LPBK
Loopback
H2TU-C-231 List 1E
Selection Description
ENA Enables a logic loopback at the H2TU-R when an LOS occurs at its DS1 input,
if enabled at the H2TU-R. For priority resolution, see
DIS Disables Transmit Loss of Signal (TLOS) logic loopback.
AIS Enables the H2TU-R to transmit an AIS towards CI for any network loopback.
For priority resolution, see
LOS Enables the H2TU-R to transmit an LOS towards CI for any network loopback.
Selection Description
OFF Disables powering to the HDSL2 pair.
ON Keeps the HDSL2 line voltage at nominal -185 Vdc.
ENA Enables remote provisioning.
DIS Disables remote provisioning.
ENA Enables BPVs and HDSL2 CRC errors at the DS1 input to be converted into
DS1 BPVs at the DS1 output at the distant end. This makes HiGain HDSL2
transparent to BPVs.
DIS Disables BPV Transparency.
1E-6 System alarm relay contact closes and the Status LED flashes red when the
Block Error Rate exceeds 10
Bit Error Rate.)
1E-7 System alarm relay contact closes and the Status LED flashes red when BER
exceeds 10
NONE Prevents generation of a system alarm due to BER.
ENA Enables the fixed 24-hour DS1 BER threshold.
DIS Prevents the generation of a system alarm due to DS1 BER.
GNLB Configures the HiGain HDSL2 system to respond to the generic inband
loopback codes.
A2LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Teltrend addressable repeater.
A3LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Wescom addressable repeater.
A4LB Configures the HiGain HDSL2 system to respond to the inband loopback
codes of the Wescom Mod 1 addressable repeater.
ENA Enables the HiGain HDSL2 system to recognize all inband SmartJack (SMJK)
loopback commands.
DIS Configures the HiGain HDSL2 system to ignore all inband SmartJack
loopback commands.
April 21, 2000
Figure 24 on page
-6
. (Block Error Rate is based on the definition of
-7
.
Provisioning
Figure 24 on page 47.
47.
21