JBL CINEMA PROPACK 600 Owner's Manual page 16

Input Source Selector: Press this button
to change the input by scrolling up or down
through the list of input sources. When an
audio source is selected, the last video input
used remains routed to the Video 1 Output a
and Video Monitor Output ‚. This permits
you to simultaneously view and listen to
different sources.
FM Mode Selector: Press this button to
select Auto or Manual tuning. When the but-
ton is pressed so that the AUTO indicator
lights, the tuner will search for the next station
with an acceptable signal when the Tuning
Selector is pressed. When the
49
button is pressed so that the AUTO indicator
is not lit, each press of the Tuning Selector
will increase the frequency.
49
NOTE: When the FM reception of a station is
weak, audio quality will be increased by
switching to Mono mode by pressing the
FM (Tuning) Mode Button
STEREO Indicator goes out.
Digital Optical 2 Input: Connect the
optical digital output of an audio or video
product to this jack. When the Input is not in
use, be certain to keep the plastic cap installed
to avoid dust contamination that might
degrade future performance.
Digital Coax 3 Jack: This jack is used for
connection to the output of portable audio
devices, video game consoles or other products
that have a coax digital jack.
Video 4 Video Input Jacks: These jacks
may be used for temporary connection to the
composite or S-Video output of video games,
camcorders or other portable video products.
Video 4 Audio Input Jacks: These
audio/video jacks may be used for temporary
connection to video games or portable
audio/video products such as camcorders and
portable audio players.
14
Bass Control: Turn this control to modify
the low-frequency output of the left/right
channels by as much as ±10dB. Set this control
to a suitable position for your taste or room
acoustics.
Balance Control: Turn this control to
change the relative volume for the front
left/right channels.
NOTE:
For proper operation of the surround modes
this control should be at the midpoint, or
"12 o'clock, " position.
Treble Control: Turn this control to modify
the high-frequency output of the left/right
channels by as much as ±10dB. Set this control
to a suitable position for your taste or room
acoustics.
Volume Control: Turn this knob clockwise
until the
to increase the volume, counterclockwise to
decrease the volume. If the DCR600 is muted,
adjusting the volume control will automatically
release the unit from the silenced condition.
Set Button: When making choices during
the setup and configuration process, press this
button to enter the desired setting as shown in
the Main Information Display
DCR600's memory. The Set button may also be
used to change the display brightness, to avoid
interfering with video presentations:
Press and hold the Set Button
panel for three seconds until the message in
the Main Information Display
VFD FULL. Within five seconds, press the
front panel Selector Buttons
desired brightness display level is shown.
Press the Set Button
setting.
When FULL appears in the Main
Information Display
normal brightness. When HALF appears, the
display is at half the normal brightness level.
When OFF appears, all of the indicators in
the Main Information Display
dark. Note, however, that the Power
Indicator
you that the unit is turned on.
Once the desired brightness level is selected,
it will remain in effect until it is changed again
or until the unit is turned off.
Delay: Press this button to begin the
sequence of steps required to enter delay time
settings.
Digital Input Selector: When playing a
source that has a digital output, press this
button to select between the Optical
and Coaxial
Main Information Display: This display
delivers messages and status indications to
help you operate the receiver.
Channel Select Button: Press this button
to begin the process of trimming the channel
output levels using an external audio source.
Speaker Select Button: Press this button
to begin the process of selecting the speaker
positions that are used in your listening room.
into the
Test Tone Selector: Press this button
to begin the process of adjusting the channel
output levels using the internal test tone as
a reference.
on the front
Remote Sensor Window: The sensor
reads
behind this window receives infrared signals
from the remote control. Aim the remote at
until the
this area and do not block or cover it unless an
external remote sensor is installed.
again to enter the
, the display is at its
will go
will always remain lit to remind
e
f Digital inputs.