Black & Decker MTOS4 Original Instructions Manual page 6

ENGLISH
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
n
Do not stare at operating lamp
Additional safety instructions for batteries and
chargers
Batteries
Š Never attempt to open for any reason.
Š Do not expose the battery to water.
Š Do not store in locations where the temperature may
exceed 40 °C.
Š Charge only at ambient temperatures between 10 °C and
40 °C.
Š Charge only using the charger provided with the tool.
Š When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Chargers
Š Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Š Never attempt to charge non-rechargeable batteries.
Š Have defective cords replaced immediately.
Š Do not expose the charger to water.
Š Do not open the charger.
Š Do not probe the charger.
#
Electrical safety
This charger is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
Š If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. Super-lokTM Tool free accessory clamping lever
2. This tool includes some or all of the following accessories.
The performance of your tool depends on the accessory
used. BLACK+DECKER and Piranha ac-cessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
6
(Original instructions)
Precision plunge cut saw blade for wooden
materials, soft plastics.
(Part number - X26105-XJ) Separating, plunge
and flush cutting of wood and soft plastics.
Ideal for working on doors, skirting boards,
windowsills and flooring.
Plunge cut saw blade for wood and metal.
(Part number - X26110-XJ) Separating, plunge
and flush cutting of wood, plastics, thin-walled
non-ferrous pipes and extrusions, nails and
screws.
Plunge cut saw blade for wood and metal.
(Part number - X26115-XJ) Separating, plunge
and flush cutting of wood, plastics, thin-walled
non-ferrous pipes and extrusions.
Segmented saw blade.
(Part number - X26120-XJ) Long life blade
which is ideal for cutting wood, plastics, thin
walled ferrous and non-ferrous material.
Rigid scraper.(Part number - X26135-XJ)
Ideal for removal of hard and soft material
from flat surfaces such as the removal of vinyl
flooring, bonded carpet adhesive, tile floor
adhesive, grout, paint and varnish.
Flexible scraper.(Part number - X26140-XJ)
Ideal for removal of elastomer materials from
hard flat surfaces in difficult to reach areas such
as silicon sealant and other caulking materials.
Carbide grout removal blade.
(Part number - X26125-XJ) Carbide coated
surface ideal for clearing grout and tile adhesive
from flat surfaces and for fast stock removal of
wood, chipboard and fibreglass.
Carbide rasp.(Part number - X26130-XJ)
Carbide coated surface ideal for grout removal
and for fast stock removal of plastics,
chipboard and fibreglass.
Sanding Sheets
Various grades for sanding of wood, painted
and varnished surfaces.
@
Assembly
Warning! Before assembly, remove the battery from
the tool.
Fitting a BLACK+DECKER / Piranha acces-sory
(fig. A)
Š Hold the tool and squeeze the accessory clamping lever
(10).