Advertisement
Quick Links
FLOE QUICK ATTACH ROLL IN
LEG CONVERSION KIT
CONVERTS STANDARD ROLL-IN LEGS TO QUICK ATTACH ROLL-IN
ASSEMBLY INSTRUCTIONS
KIT P/N 510-20000-00
*DOCK NOT INCLUDED
NEVER ADJUST YOUR DOCK LEGS WITH
AN IMPACT WRENCH. NEVER ADJUST
YOUR DOCK LEGS WITH MORE THAN 15
FT-LBS OF FORCE. APPLYING TOO MUCH
FORCE TO YOUR DOCK LEGS WILL
DAMAGE THE MECHANISM.
INSTRUCTION P/N: 610-20000-00
RELEASED 9/7/22
SHEET 1 OF 16
NOTE:
REFER TO THE INSTRUCTIONS
INCLUDED WITH YOUR WHEEL
KIT FOR FURTHER
INFORMATION
TOOLS REQUIRED
-(2) 9/16" SOCKETS/WRENCHES
-3/4" WRENCH/SOCKET
-CORDLESS DRILL WITH SOCKET
ADAPTER & 1-1/8" SOCKET OR
FLOE SPEED WRENCH
-TORQUE WRENCH
-TAPE MEASURE
-LEVEL
-BLOCKING MATERIAL
© Manufactured by:
Floe International Inc.
48473 State Hwy. 65
McGregor, MN 55760
www.floeintl.com
Advertisement
Related Manuals for Floe 510-20000-00
Summary of Contents for Floe 510-20000-00
- Page 1 FLOE QUICK ATTACH ROLL IN LEG CONVERSION KIT CONVERTS STANDARD ROLL-IN LEGS TO QUICK ATTACH ROLL-IN ASSEMBLY INSTRUCTIONS KIT P/N 510-20000-00 NOTE: REFER TO THE INSTRUCTIONS INCLUDED WITH YOUR WHEEL KIT FOR FURTHER INFORMATION *DOCK NOT INCLUDED TOOLS REQUIRED -(2) 9/16” SOCKETS/WRENCHES -3/4”...
- Page 2 BILL OF MATERIALS/EXPLODED VIEW 510-20000-00 KIT, QA ROLL-IN LEG CONVERSION NUMBER PART NUMBER QTY. DESCRIPTION 001-02346-00 FASTENERS, QA ROLL-IN LEG CONVERSION KIT 002-00285-00 BRACKET, QA DOCK SIDE BRACE 002-00291-00 QUICK CONNECT, QA ROLL-IN – 2” 001-02346-00 FASTENERS, QA ROLL-IN LEG CONVERSION KIT...
- Page 3 STEP 1 (MEDIUM WHEEL KIT INSTALLATION IS SHOWN) TURN DOCK UPSIDE DOWN AND BLOCK CORNERS (OR USE A SOFT SURFACE) TO PROTECT THE DECK SURFACE (FIGURE 1.1). INSTALL (1) 1/2" X 1” BOLT AND (1) 1/2" NUT INTO EACH POCKET WELDED ON THE DOCK (INCLUDED WITH WHEEL KIT) (FIGURE 1.2).
- Page 4 INSERT WHEEL KIT LEGS INTO THE POCKETS THAT ARE WELDED ON THE DOCK (NOT INCLUDED KIT) (FIGURE 1.4). UNDER NORMAL CONDITIONS, THE WHEEL KITS ARE MOUNTED AS SHOWN IN FIGURE 1.5A. IF NECESSARY, WHEEL KITS MAY BE TURNED 180° FOR BOAT LIFT CLEARANCE. HOWEVER, SOME STABILITY MAY BE LOST (FIGURE 1.5B).
- Page 5 STEP 2 ATTACH THE 26” CENTER BRACES TO THE WHEEL KIT LEG BRACKET USING (1) 3/8” X 5” BOLT, (2) 3/8” WASHERS, AND (1) 3/8” NUT PER SIDE (INCLUDED WITH WHEEL KIT) (FIGURE 2.1). ATTACH THE 26” SIDE BRACES TO THE WHEEL KIT BRACKET USING (1) 3/8” X 1-3/4” BOLT, (2) 3/8” WASHERS, AND (1) 3/8”...
- Page 6 ATTACH THE 26” SIDE BRACES TO THE INCLUDED SIDE BRACE BRACKET USING (1) 3/8” X 1-3/4” BOLT, (2) 3/8” WASHERS, AND (1) 3/8” NUT PER SIDE (INCLUDED WITH WHEEL KIT) (FIGURE 2.3). CONNECT THE END(S) OF THE (2) CENTER BRACE(S) TO THE BRACKET ON THE DOCK USING (1) 3/8”...
- Page 7 THE ENDS OF THE TWO SIDE BRACES ARE ATTACHED TO THE DOCK BY PLACING THE SIDE BRACE BRACKETS INTO THE DOCK SIDE (FIGURE 2.5 & 2.5A). FIGURE 2.5 *FOR X-DEEP & XX- DEEP WHEEL KITS *FIGURE 2.5A SHEET 7 OF 16...
- Page 8 INSERT (2) 3/8” X 1” BOLTS INTO THE BOTTOM OF THE BRACKET (FIGURE 2.6). TORQUE TO 6 FT-LBS MAXIMUM (FIGURE 2.7). TORQUE ALL 3/8” NUTS INSTALLED IN THIS STEP TO THE TORQUE SPECIFICATIONS SHOWN. OVERTIGHTENING THE FASTENERS WILL CRUSH THE BRACES (FIGURE 2.8). *FIGURE 2.6 *4X FOR X-DEEP &...
- Page 9 STEP 3 SLIDE WHEEL(S) (SOLD SEPARATELY) ONTO THE SPINDLE ON THE WHEEL KIT AND PLACE A 2-1/2” WASHER ONTO THE SPINDLE (INCLUDED WITH WHEEL KIT) (FIGURE 3.1). INSERT SPINDLE CLIP LEG INTO ONE OF THE HOLES IN THE SPINDLE, THEN PULL CLIP DOWN TO SNAP OTHER CLIP LEG INTO THE SECOND HOLE (INCLUDED WITH WHEEL KIT) (FIGURE 3.2).
- Page 10 THE INNER LEG SHOULD BE ADJUSTED NOW BY LOOSENING THE 1/2" SET BOLT AND EXTENDING THE INNER LEG (FIGURE 3.3). SEE THE CHART BELOW AND FIGURE 3.3 FOR APPROXIMATE INNER LEG EXTENSION. USE THIS CHART AS A REFERENCE. NEVER EXCEED 16” OF EXTENDED LENGTH. (THIS STEP IS NOT NECESSARY FOR DEEP, X-DEEP, AND XX-DEEP WHEEL KITS) FIGURE 3.3 EXTENDING THE INNER WHEEL KIT LEG MORE...
- Page 11 TORQUE TO 40 FT-LBS ONCE LEG HEIGHT IS SET (FIGURE 3.4). FIGURE 3.4 SHEET 11 OF 16...
- Page 12 STEP 4 TURN DOCK RIGHT SIDE UP (FIGURE 4.1). ATTACH QUICK CONNECTS TO THE WHEEL KIT END OF THE DOCK SECTION IF ANOTHER SECTION IS TO BE CONNECT TO IT. TO ATTACH DOCK SECTIONS IN A STRAIGHT LINE, QUICK CONNECTS SHOULD BE ASSEMBLED AS SHOWN. SPACE THE QUICK CONNECTS AS FAR OUT AS POSSIBLE (FIGURE 4.2).
- Page 13 WHEN ANOTHER DOCK SECTION CONNECTS TO A SIDE OF THE DOCK, QUICK CONNECTS SHOULD BE PLACED AS SHOWN (FIGURE 4.3). ATTACH USING A 3/8” X 1” BUTTON HEAD BOLT (FIGURE 4.4). FIGURE 4.3 FIGURE 4.4 SHEET 13 OF 16...
- Page 14 TORQUE BOLTS TO 5 FT-LBS (FIGURE 4.5). QUICK CONNECTS SHOULD BE SPREAD APART AS FAR AS POSSIBLE TO KEEP THE JOINING SECTION FROM SHIFTING SIDEWAYS. PLACE CONNECTING DOCK SECTIONS IN THE QUICK CONNECT INSTALLATION/REMOVAL POSITION WHEN INSTALLING OR REMOVING MULTIPLE SECTIONS. PUSH THE DOCKS INTO POSITION IN THE WATER. ONCE THE DOCKS ARE IN POSITION, PUT THEM IN THE QUICK CONNECTS SET POSITION (FIGURE 4.6).
- Page 15 WITH THE CAP REMOVED FROM THE DOCK, USE A FLOE SPEED WRENCH OR 1-1/8” SOCKET AND CORDLESS DRILL TO ADJUST THE HEIGHT OF THE DOCK SO THE BOTTOM FRAME OF THE DOCK IS APPROXIMATELY 8” ABOVE THE WATER. *SEE NOTE ON SHEET 1. TURN THE DOCK ADJUSTING NUT ON THE TOP OF THE DOCK CLOCKWISE TO LOWER THE DOCK AND COUNTERCLOCKWISE TO RAISE THE DOCK.
- Page 16 NOTES SHEET 16 OF 16...
- Page 17 SHEET 17 OF 16...