Clothing; Operating The Tiller; Operation Zone; Adjusting The Wheel/ Depth Skid - Texas Equipment FRZ 5800 User Manual

Before winter storage, the battery should be fully charged
and kept warm at 10-20 degrees C. Charge it every 3
months. Make sure to keep ventilation holes clean and free
from dirt.
Store the charger indoor between 5-25 degrees C.
The battery cells will go to sleep-mode if ont used for
long time and must be activated again to reach full
capacity. The battery will reach its full power after 5 full
recharge cycles. Therefore, you might experience that
for the first few times uses, the battery's operating
time is a few minutes less than when it reaches its full
power/capacity. This is also the case after long times
winter storage.

Clothing

When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface with the
support wheels lowered prior to start.
Remove all foreign objects from the work area before
using the machine. Stones, glass, branches and similar
items may damage the tiller. Also, check the bolts on the
tiller are tightened.
Start the motor as per the instructions below. Stand
clear of the machine's moving parts.
The tiller is designed for use in vegetable gardens and
flowerbeds. Ensure that you are familiar with these
instructions before operating the machine, in particular the
start and stop procedures.
Warning: Stay out of dashed zone, while starting the engine!
Always start the engine from dotted operation zone.
See illustration 13.
Safety key. See illustration 14
The motor unit has a safety key, which is placed under the
battery cover. If the safety key is removed, the power is
disconnected, and it cannot start.
It is always recommended to remove the safety key:
•
When the machine is left unattended (to prevent
uninteded start, e.g. by minors)
•
Before clearning and maintenance
To remove the safety key, turn it to the free position "O" and
pull it out. To insert the safety key, inset it and turn it to run
position "I". Only then the motor can start.
Start (Illustration 15 + 16)
1. Turn the safety key to the run position "I"
2. Press the button on the control panel once and it lights
up green with "turtle" (slow speed).
3. Press the button on the control panel once more and it
lights up yellow at "rabbit" (fast speed).
Subsequent fast presses toggle between slow and fast
speed.
4. Hold down the safety button (1) and activate the clutch
lever (2).
Reverse speed
To use the reverse gear function, hold down the button so
that it lights up red at "R". The button must be held down as
long as go reverse. When the button is released, the function
returns to slow forward speed (turtle) and blades stop
turning.
Stop
Release the clutch lever. Turn the safety key to "O".
After 5 minutes of inactivitythe whole system will shut down
automatically.
Remove the battery
To remove the battery, press and hold both latch buttons on
the battery and pull it out (Illustration 17)
There is space for an addtional battery in the motor unit. This
can be purchased seperately.
If 2 batteries are being used, the active battery must be
placed in the right socket "(viewed from front)". The battery
socket in left side is only for storage.
Working time
The working time per full charge depends of several factors,
like working speed (gear choice), soil hardness, temperature
and if weed is growing in the soil.
Tips
Do not start motor before machine is at area to be worked.
Always hold machine securely in both hands.
The blades will propel the machine forwards. Allow the
blades to slowly sink into the soil.
Remember to adjust the depth skid before use.
When cutting deeply, the most effective method is to allow
the blades to propel the machine forwards for an arm's
length. Pull the machine back towards you. Allow it to run
forwards again. Blades must always operate at maximum
speed. Avoid overloading If the blades get buried, rock
machine from side to side while holding it back, until it comes
free
Vibrations may travel up into the handle during
use. We therefore recommend taking a break
every 30 minuttes.

Operation zone

While the machine is being operated and the motor is
running, do not leave the operation zone marked illustration
13. If it is necessary to leave the operation zone, for example
to attach an accessory, first stop the engine.
It is normally necessary to drive the tiller over a section of
earth 2-3 times from different directions. Do not till very wet
soil, as clods of earth will form that are difficult to break up.

Adjusting the wheel/ depth skid

Fig. 9: Use the support wheels for transportation.
Fig. 10. The depth skid can be set in different depths. The
deeper it extends into the soil, the deeper the tilling blades
will work and the slower the machine will advance. Setting
the correct tilling depth will significantly reduce the effort
required. The depth skid should always be adjusted to suit
the ground conditions. We recommend testing several
depths to see which works best.

Lubrication of gearbox

The gearbox is permanently lubricated at the factory, never
open the gearbox.
13