& M6 & M9 MERGERS READ AND UNDERSTAND THIS MANUAL WARNING BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH. PARTS & OPERATOR’S INSTRUCTIONS 2-9-2007 Manufactured By H&S MANUFACTURING CO., INC.
AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS H&S DEALER PRE-DELIVERY CHECK LIST After the Mini Merger has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.
ALERT! YOUR SAFETY IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.
RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the poten- tial for personal injury. Follow recommended precautions and safe operating practices. UNDERSTAND SIGNAL WORDS A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol.
STAY CLEAR OF SHUT ENGINE COMPLETELY OFF BEFORE MOVING PARTS ADJUSTING OR SERVICING MACHINE. FAILURE TO HEED THIS MACHINE MAY START UNEXPECTEDLY WARNING MAY RESULT IN FAILURE TO HEED THIS WARNING MAY RESULT PERSONAL INJURY OR DEATH IN PERSONAL INJURY OR DEATH 3398C KEEP CLOTHING, YOURSELF AND OTHERS WELL CLEAR.
H&S 6’ & 9’ MERGER W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
OPERATION Check entire unit carefully before first operation. Tighten bolts and set screws that might have come loose in handling. Lubricate as explained in the lubrication guide. Adjust tractor drawbar to allow for maximum clearance between drawbar and ground. Attach merger to tractor with a hitch pin that has a safety locking device.
TRANSPORT LOCK STAY CLEAR OF MOVING PARTS FAILURE TO HEED THIS WARNING MAY RESULT IN PERSONAL INJURY OR DEATH KEEP CLOTHING, YOURSELF AND OTHERS WELL CLEAR. 3398A Transport Position Located on the right side of the pick-up on the lift cylinder is the manual valve which locks the pick- up into transport position.
ADJUSTMENTS TAIL WHEEL The tail wheel is located at the right rear of the merger. Located on the tail wheel pivot spindle is an adjustable brake assembly. Adjust brake by tightening bolt (A). The brake should have enough tension to prevent zig-zag motion, but still allow the wheel to pivot when making corners.
Page 12
ADJUSTMENTS (Continued) PICKUP HEAD The pickup head should be adjusted accord- ing to the height of the stubble. Pickup height is adjusted by adjusting the gauge wheels located at both sides of the pickup head. Remove adjustment pin (A) and place in the desired hole position above the gauge wheel arm.
HYDRAULICS There are four hydraulic hoses from the merger to the tractor. The two smaller, (3/8’’ diameter) hoses pro- vide oil to the pickup lift cylinder (A). The two larger (1/2’’ diameter) hoses provide oil to the hydraulic motors (B) running pickup belt and cross conveyor belt.
Page 14
LUBRICATION There are 18 grease fittings on your merger, 20 if equipped with an accelerator. If these are lubricated properly and often enough, it will prolong the life of the merger. Grease daily during normal use, and before and after storage. Use a good grade of high quality grease. Make sure grease comes out around the shaft on sleeve type bearings.
OPTIONAL ACCELERATOR AND INVERTER ACCELERATOR Remove accelerator for road transport INVERTER Transport Position Working Position Remove inverter for road transport -16-...
INSTRUCTIONS FOR ORDERING PARTS All service parts should be ordered through your authorized H&S dealer. He will be able to give you faster service if you will provide him with the following. 1. Model & Serial Number - Both can be located on the right side main frame of your unit. 2.
DECAL LOCATION Your H&S 6’ & 9’ Merger was manufactured with operator safety in mind. Located on the windrow merger are various decals to aid in operation, and warn of danger or caution areas. Pay close attention to all the decals on your Mini Merger.
H&S 6’ & 9’ MERGERS Your new H&S Mini Merger has been manufactured of the finest quality materials and compo- nents. The performance you get from your machine is largely dependent upon how well you read and understand this manual and apply this knowledge. There is a right and a wrong way to do everything.
Page 34
S MFG. CO. & products approved for the FEMA SEAL OF QUALITY...