Table of Contents
Advertisement
Quick Links
STANDARD DUTY
STANDARD DUTY
SPREADER
SPREADER
READ AND UNDERSTAND THIS MANUAL BEFORE
READ AND UNDERSTAND THIS MANUAL BEFORE
OPERATING THIS EQUIPMENT. UNSAFE OPERATION
OPERATING THIS EQUIPMENT. UNSAFE OPERATION
OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT
OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT
IN SERIOUS INJURY OR DEATH.
IN SERIOUS INJURY OR DEATH.
Revision #00
Starting Serial #222PD17001
2217
2217
WARNING
WARNING
O O
P P
E E
R R
A A
T T
O O
R R
S S
Part#91916
Part#91916
Rev. #00
Rev. #00
M
M
A A
N N
U U
A A
L L
HSMFG1221
HSMFG1221
Advertisement
Table of Contents
Related Manuals for H&S 2217
Summary of Contents for H&S 2217
- Page 1 2217 2217 STANDARD DUTY STANDARD DUTY SPREADER SPREADER WARNING WARNING READ AND UNDERSTAND THIS MANUAL BEFORE READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH.
-
Page 2: Table Of Contents
CONTENTS Warranty ..............1 Manufacturer’s Statement . -
Page 4: Manufacturer's Statement
H&S reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products previously manufactured. Specifications, statements and descriptions of Products contained in this publication are subject to change without prior notification. - Page 6 Intentionally Left Blank...
-
Page 7: Pre-Delivery Checklist
DEALER PRE-DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Manure Spreader has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. - Page 8 Intentionally Left Blank...
-
Page 9: Delivery Checklist
DEALER DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This checklist that follows is an important reminder of valuable information that should be passed on to the customer at the time this Manure Spreader is delivered. Check off each item as you explain it to the customer. This delivery checklist, when properly filled out and signed, assures the customer that the pre-delivery service was satisfactorily performed. - Page 10 Intentionally Left Blank...
-
Page 11: Safety Information - Be Alert Symbol
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. -
Page 12: Explanation Of Safety Signs
SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. -
Page 13: Safety Decals
SAFETY INFORMATION -11-... - Page 14 SAFETY INFORMATION -12-...
-
Page 15: Safety Information - Warning - Owner Must Read And Understand
SAFETY INFORMATION TRACTOR: This operator’s manual uses the term “Tractor” when identifying the power or the towing source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. -
Page 16: Cap Screw Torque Values
-14-... -
Page 17: Set-Up & Assembly
SET-UP & ASSEMBLY NOTE: Determine right or left side of the Manure Spreader by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to the Cap Screw Torque Value Chart. PREPARING MANURE SPREADER The Manure Spreader may be shipped without the wheels/tires installed. 1. -
Page 18: Preparing For Operation
PREPARING FOR OPERATION TRACTOR CONNECTIONS Tractor Hitch Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from pipe mount and place on convenient storage mount located on the left front of spreader. -
Page 19: Operation
OPERATION LOADING In freezing weather, make certain that hydraulic tail gate (if equipped with one) is not frozen to the sides or on the floor of the spreader. Make sure the apron chain is not frozen to the spreader floor or any lumps of manure are frozen to the floor. -
Page 20: Adjustments
ADJUSTMENTS DRIVE CHAIN Shields Removed For Clarity To adjust front drive chain, slightly loosen bolts holding pillow block bearing at rear of front jack shaft. Loosen jam nut on tightener rod. Turn adjusting nut (located at the right hand front side of spreader) clockwise. - Page 21 ADJUSTMENTS APRON 1. Adjust the apron by loosening the mounting bolts on the chain slides on the outside of the frame. Mounting bolts shown in the drawing. 2. Tighten the adjusting bolts until the apron has no sag between the rear drive sprockets and chain slides under spreader.
-
Page 22: Service
SERVICE SHEAR BOLTS - Main Drive The beater and the apron drive are protected by one shear bolt located on the front end of the side drive shaft (left side of spreader). Two spare shear bolts are provided. Shearing of the bolts is normally due to foreign objects in the manure or starting the spreader PTO too quickly with high tractor RPMs. - Page 23 SERVICE TIRES & WHEELS Check the tire pressure after every 50 hours of operation. Tires should be inflated to the appropriate pressure listed in the table. Tire Pressure 10.00x22.5 75-85 PSI Wheel lug torque should be checked after every 50 hours of operation and tightened to the appropriate torque.
-
Page 24: Optional Equipment
OPTIONAL EQUIPMENT REAR PAN The rear pan shown below is optional equipment. REAR PAN SEMI-LIQUID HYDRAULIC ENDGATE The semi-liquid hydraulic endgate is also optional. The rear pan and hydraulic endgate may be used together on this model. HYDRAULIC ENDGATE TOP BEATER The top beater shown below is optional equipment. -
Page 25: Lubrication Guide
LUBRICATION The operator should become familiar with all lubrication points and establish a systematic routine to ensure complete and quick lubrication of the machine. GENERAL INFORMATION IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components, valves, cylinders, hoses, etc. - Page 26 LUBRICATION GREASE ZERK LOCATIONS (1) at each end of the input shaft (1) on each front idler sprocket behind the shields (1) at each end of (1) on jack the PTO shaft (1) on the side shaft on each hydraulic endgate arm pivot if applicable...
-
Page 27: Decal Location
DECAL LOCATION Your Manure Spreader was manufactured with operator safety in mind. Located on the Manure Spreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attention to all decals on your Manure Spreader. DO NOT REMOVE ANY OF THESE DECALS. - Page 28 DECAL LOCATION DCAMB 111593C 093020 DCAMB 11593A 093020 91834 91832 DCRED 093020 11211176 1494A (Under Shield) 093020 -26-...
- Page 29 DECAL LOCATION 093020 111593C 5HP111593A 5HP1494K 5HP1494J 5HP66076 12794 DCAMB 093020 91833 DCAMB 12794 72538 9194B 1494K 66076 91831 71494A BEHIND SHIELD -27-...
- Page 30 DECAL LOCATION 1494A BEHIND SHIELD 1494B 9194A 71188B 82602 093466 54033 72203A 91835 91836 DCAMB 1494L 093020 1494J 11211176 82793 1494B 66076 9194B 9194A -28-...
-
Page 31: Troubleshooting
TROUBLESHOOTING WARNING: MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CANNOT MOVE BEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY. TROUBLE... POSSIBLE CAUSE... POSSIBLE REMEDY... Beater Does Not Turn PTO Not Turning Engage Tractor PTO Beater Not Engaged... -
Page 32: Service Notes
SERVICE NOTES -30-... - Page 34 H&S MFG. CO. products approved for the FEMA SEAL OF QUALITY Manufactured by: H&S MANUFACTURING CO., INC. 2608 S. HUME AVE. MARSHFIELD, WI 54449 (715) 387-3414 | hsmfgco.com...