Page 1
Especially, procedures to write bootloader to each board are explained. Bootloaders are written to the Flash ROM on the board using the Flash Writer or the Mini Monitor provided by Renesas. This document explains the way to write these files using the Flash Writer. Target RZ/G2 Group reference boards •...
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Preparing Flash Writer Flash Writer is built automatically when building BSP by bitbake command. Please refer to the Release Note of the Verified Linux Package to obtain a binary file of Flash Writer.
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Hoperun Technology HiHope RZ/G2[HMN] platform (hihope-rzg2h, hihope- rzg2m, hihope-rzg2n) Preparation 1.1.1 Building files to write This board uses the files below as a bootloader. Please build them according to the Release Note and copy these files to the PC which runs a serial terminal software.
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Booting Flash Writer Turn on the power of the board by changing the SW2402. Messages below are shown on the terminal. SCIF Download mode (w/o verification) (C) Renesas Electronics Corp.
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide The image will be sent to the board via serial connection. After successfully download the binary, Flash Writer starts automatically and show a message like below on the terminal. Flash writer for RZ/G2M V1.00 Sep.24,2019 >...
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Please Input : H'000000 Work RAM(H'50000000-H'53FFFFFF) Clear..please send ! ('.' & CR stop load) Send the data of “bootparam_sa0.srec” from terminal software after the message “please send !” is shown.
Page 8
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide SW1002 Note) Be careful not to change the SW1001 and SW1003 Turn on the power of the board by changing the SW2402. U-Boot 2020.10 (May 07 2021 - 13:48:35 +0000) CPU: Renesas Electronics R8A774A1 rev 1.1/rev 1.2...
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Silicon Linux RZ/G2E evaluation kit (EK874) Preparation 2.1.1 Building files to write This board uses the files below as a bootloader. Please build them according to the Release Note and copy these files to the PC which runs a serial terminal software.
Page 10
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Booting Flash Writer. R01US0555EJ0100 Rev.1.00 Page 10 of 13 Mar. 31, 2022...
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide After successfully download the binary, Flash Writer starts automatically and shows a message like below on the terminal. Flash writer for RZ/G2E V1.00 Sep.24,2019 > Writing Bootloader “XLS2” command of Flash Writer is used to write binary files. This command receives binary data from the serial port and write the data to specified address of the Flash ROM with information where the data should be loaded on the address of the main memory.
Page 12
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide => env default -a ## Resetting to default environment => saveenv Saving Environment to SPI Flash... SF: Detected w25m512jv with page size 256 B ytes, erase size 4 KiB, total 32 MiB Erasing SPI flash...Writing to SPI flash...done...
Page 13
Reference Boards of RZ/G2H, RZ/G2M, RZ/G2N, and RZ/G2E Start-up Guide Website and Support Renesas Electronics Website http://www.renesas.com/ Inquiries http://www.renesas.com/contact/ All trademarks and registered trademarks are the property of their respective owners. R01US0555EJ0100 Rev.1.00 Page 13 of 13 Mar. 31, 2022...