Table of Contents
Advertisement
Quick Links
RZV2M SMARC SOM
Start-Up Guide
Contents
1.
Overview ................................................................................................................................. 2
1.1
Features .................................................................................................................................................. 2
2.
Operating environment ............................................................................................................ 2
3.
Carrier Boards ......................................................................................................................... 3
3.1
TQ-Group Carrier Board .......................................................................................................................... 3
3.2
Congatec Carrier Board .......................................................................................................................... 4
3.3
Kontron Carrier Board ............................................................................................................................. 4
4.
How to run the SMARC Module ............................................................................................... 4
4.1
SMARC SOM Settings ............................................................................................................................ 5
4.1.1
SMARC SOM Switch Settings .............................................................................................................. 5
4.1.2
SMARC SOM MIPI-CSI Settings .......................................................................................................... 5
4.2
Carrier Board Settings ............................................................................................................................. 6
4.2.1
MB-SMARC-2SMARC 2.0/2.1 Carrier board ........................................................................................ 6
4.3
Cable Settings ......................................................................................................................................... 7
4.3.1
Debugging cable settings ...................................................................................................................... 7
4.3.2
Terminal software .................................................................................................................................. 7
4.3.3
Serial port settings ................................................................................................................................. 7
4.4
SD Card Settings ..................................................................................................................................... 9
4.5
GBE Settings ........................................................................................................................................... 9
4.6
HDMI Settings ....................................................................................................................................... 10
4.7
Power Supply Settings .......................................................................................................................... 10
4.8
Startup ................................................................................................................................................... 11
4.8.1
Run the Sample Applications .............................................................................................................. 11
4.8.1.1 Run the MIPI-CSI to HDMI Application ............................................................................................. 11
4.8.1.2 Run the MIPI-CSI to VCD Application ............................................................................................... 11
4.8.1.2.1 Configure the VLC Media Player....................................................................................................... 12
4.8.1.2.2 Create the SDP file............................................................................................................................ 13
4.8.1.2.3 Start the MIPI-CSI to VCD application on RZV2M SMARC SOM. ................................................... 14
4.8.1.2.4 Play the video stream on VLC ........................................................................................................... 16
4.8.2
Shutdown ............................................................................................................................................ 16
References ................................................................................................................................... 17
Revision History ............................................................................................................................ 18
Revision 1.2
September 2021
RZV2M SMARC SOM - Start-Up User Guide
Page 1 of 18
Advertisement
Table of Contents
Related Manuals for Renesas RZV2M SMARC SOM
Summary of Contents for Renesas RZV2M SMARC SOM
-
Page 1: Table Of Contents
4.8.1.2 Run the MIPI-CSI to VCD Application ....................11 4.8.1.2.1 Configure the VLC Media Player....................... 12 4.8.1.2.2 Create the SDP file..........................13 4.8.1.2.3 Start the MIPI-CSI to VCD application on RZV2M SMARC SOM............ 14 4.8.1.2.4 Play the video stream on VLC ......................16 4.8.2 Shutdown ............................ -
Page 2: Overview
Start-Up Guide 1. Overview 1.1 Features 2. Operating environment The recommended environment for the RZV2M SMARC SOM is shown in Figure 1. Figure 1. Recommended environment The equipment and software are listed in Table 1. Table 1. Equipment and Software... -
Page 3: Carrier Boards
3. Carrier Boards The RZV2M SMARC SOM cannot be used as an independent module. It must be used in conjunction with SMARC Carrier boards. The RZV2M SMARC SOM is compatible with any SMARC 2.0/2.1 carrier board available on the market. -
Page 4: Congatec Carrier Board
4. How to run the SMARC Module Plug in the RZV2M SMARC SOM into the SMARC 2.0/2.1 carrier board and fix the mechanical connection by using the proper screws. The connection of the RZV2M SMARC SOM to TQ’s MB-SMARC-2SMARC 2.0/2.1 carrier board is shown in Figure 3. -
Page 5: Smarc Som Settings
RZV2M SMARC SOM Start-Up Guide 4.1 SMARC SOM Settings 4.1.1 SMARC SOM Switch Settings Confirm the switch settings shown in the red frame in Figure 4. Figure 4. RZV2M Switch Settings 4.1.2 SMARC SOM MIPI-CSI Settings Connect the MIPI-CSI Camera (FRAMOS IMX415 module or any equivalent) to SOM’s camera interface as highlighted in Figure 5. -
Page 6: Carrier Board Settings
RZV2M SMARC SOM Start-Up Guide Figure 5. RZV2M SMARC SOM MIPI-CSI Interface 4.2 Carrier Board Settings 4.2.1 MB-SMARC-2SMARC 2.0/2.1 Carrier board Confirm the switch S3 settings shown in the red frame in Figure 6. Figure 6. MB-SMARC-2SMARC 2.0/2.1 Carrier board Switch Settings Revision 1.2... -
Page 7: Cable Settings
RZV2M SMARC SOM Start-Up Guide 4.3 Cable Settings 4.3.1 Debugging cable settings Connect the debugging DB9 cable adapter to X39 connector of the MB-SMARC-2SMARC 2.0/2.1 carrier board (X39 is available on the bottom side of the carrier board). SER0-RS232 interfaces in highlighted in Figure 7. - Page 8 RZV2M SMARC SOM Start-Up Guide A. Menu -> Setup -> Serial port Figure 8. Terminal software settings B. Menu -> Setup -> Terminal Figure 9. Terminal software settings Revision 1.2 Page 8 of 18 September 2021...
-
Page 9: Sd Card Settings
RZV2M SMARC SOM Start-Up Guide 4.4 SD Card Settings Plug in the uSD card on the SD CARD slot (X16) of the MB-SMARC-2SMARC 2.0/2.1 Carrier. X16 interface is highlighted in Figure 10. Figure 10. MB-SMARC-2SMARC 2.0/2.1 Carrier board uSD Card Interface 4.5 GBE Settings... -
Page 10: Hdmi Settings
RZV2M SMARC SOM Start-Up Guide 4.6 HDMI Settings Plug in the HDMI Monitor cable on the HDMI interface (X6) as shown in Figure 12. Figure 12. MB-SMARC-2SMARC 2.0/2.1 Carrier board HDMI Interface 4.7 Power Supply Settings MB-SMARC-2SMARC 2.0/2.1 Carrier board can be supplied with a DC voltage between 14VDC to 36VDC either on X13 or on X12. -
Page 11: Startup
In order to setup the system, the following information is needed: The IP of the PC where VLC media player is running. The IP of the RZV2M SMARC SOM module. Revision 1.2 Page 11 of 18 September 2021... -
Page 12: Configure The Vlc Media Player
RZV2M SMARC SOM Start-Up Guide Session Description Protocol (SDP) file for VLC multimedia session. Also, some additional settings are needed for the VLC Media Player. 4.8.1.2.1 Configuration of the VLC Media Player After installing the VLC Media Player, please make the bellow settings: a) Open preferences window from Tools ->... -
Page 13: Create The Sdp File
Figure 18. Setting Network cashing (ms) and Clock jitter properties. 4.8.1.2.2 Create the SDP file For SDP file creation, the RZV2M SMARC SOM IP is needed. The IP can be found by typing ifconfig in the serial terminal window as shown in Figure 19. -
Page 14: Start The Mipi-Csi To Vcd Application On Rzv2M Smarc Som
Create a new file on the PC and save it with .sdp extension, e.g. RTP264.sdp. Write the following content into the file and replace the RZV2M SMARC SOM IP with the correct one obtained above. For H265 encoding, the content of the file shall be as below. - Page 15 RZV2M SMARC SOM Start-Up Guide Figure 20. Find PC’s IP using ipconfig. To start the mipi to vcd application run the commands shown below and in Figure 21. The parameters of the application shall be the PC’s IP found above and the coding type used in the *scd file.
-
Page 16: Play The Video Stream On Vlc
4.8.1.2.4 Play the video stream on VLC In order to play the RZV2M SMARC SOM camera stream on VLC either double click on the sdp file created in Chapter 4.8.1.2.2 or open the VLC Media Player, go to menu Media -> Open File (or CTRL + O) and load the file created in Chapter 4.8.1.2.2, as shown in Figure 22. -
Page 17: References
RZV2M SMARC SOM Start-Up Guide References [1] Renesas Electronics, “RZ/V2M Linux Package Start-Up Guide Rev.1.00”. [2] Renesas Electronics, “RZ/V2M Linux Package Version 0.10”. [3] TQ-Group, “MB-SMARC-2 User’s Manual”. [4] TQ-Group, “MB-SMARC-2 Technical Specification” [5] FRAMOS, “FSM-IMX415 Datasheet”. Revision 1.2 Page 17 of 18... -
Page 18: Revision History
RZV2M SMARC SOM Start-Up Guide Revision History Description Rev. Date Page Summary 06.09.2021 Initial version. 07.09.2021 Add MIPI-CSI Camera Interface. 13.09.2021 1, 11 to 16 Add mipi to vcd application start-up in chapter 4.8.1. Revision 1.2 Page 18 of 18... - Page 19 Unit Products The following usage notes are applicable to all Microprocessing unit and Microcontroller unit products from Renesas. For detailed usage notes on the products covered by this document, refer to the relevant sections of the document as well as any technical updates that have been issued for the products.
- Page 20 Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or other Renesas Electronics document.